Solution for Replacing OEM 7-Way With EZ Connector on 2020 Toyota Tundra

Question

Question:

I have a 2020 Tundra with the factory tow package and factory tow connector with an integrated factory brake controller. My current connector on my truck is the 7 pin blade style with the 4 pin connector integrated next to the 7 pin/blade connector. I never use the 4 pin nor will I ever use it. But my question is, is there an adaptor that I can use to install the EZ Connector on my truck so the connection installation looks factory? See picture attached

asked by: Gregory T

0

Expert Reply:

I do have a solution, but there is not an adapter that would allow you to replace the OEM connection and keep the factory look on your 2020 Tundra. Since nothing will match that cutout, I have two options that will allow you to use the EZ Connector on your truck.

The first is to use the Trailer Connector Adapter # EZ94ZR. This will plug into your current 7-way and allow you to connect with your trailer's EZ Connector. However, you will either have to leave it plugged in or plug and unplug it each time you use it like your typical 7-way.

The other option would be the installation of the EZ Connector Magnetic 5th Wheel/Gooseneck Pigtail Harness w/ 7-Way Connector # 319-S7-08. To maintain a factory look on the bumper you could leave the OEM connector in place and install this on the opposite side instead of installing it in the truck bed. This will give you a clean look while also maintaining the other 4-way and 7-way should you ever need it.

expert reply by: Robin H

0

OEM 7-Way On 2020 Toyota Tundra
(click to enlarge)

Answer 1

Thank you for all of the information and your photo! It really looks like you've done your research with all of the various solutions you've looked at to try to prevent damaging the connection between your Lance Truck Camper and your 2019…

view full answer...

Answer 2

If you are going to change connectors the EZ Connector Magnetic 7-Way Trailer Connector #319-S7-10 would be the route I recommend going. Unlike your 7-way blade and 7-way round connectors this connector does not have any form of tension connector…

view full answer...

Answer 3

Hey Zach, to convert the 4-way of your 2017 Toyota Highlander to a 7-way and install a brake controller requires the adapter part #ETBC7. This comes with everything needed to make the conversion as well as wire in a brake controller. If your current…

view full answer...

Answer 4

If you've broken or lost any of your hardware when installing your hitch all you need is to go to part #RHK, type your hitch item number in and select the manufacturer. This will give you a complete hardware kit to replace yours. You can buy a…

view full answer...

Answer 5

We do carry replacement hardware for the Draw-Tite Trailer Hitch Receiver #75758, though just two bolts by themselves are not available, as you'll need the entire hardware kit with the Replacement Hardware Kit for Trailer Hitches #RHK. To order…

view full answer...

Answer 6

Hey Robert, we only carry the Bulldog BX1 with the part #BD1289200300 which includes the outer tube bracket. Bulldog does not offer just the inner tube.

view full answer...

Answer 7

It sounds like the right hand turn and brake signal lights are not working on your trailer. If that is the case then the first place to check as you mentioned is the fuse box. In the fuse box located under the hood of your 2016 Ram 3500 you will want…

view full answer...

Answer 8

Congrats on the new motorhome! I was looking at the features that came with your 2024 Dynamax Dynaquest XL. It does not look like it came prepped for a flat towing set up so you're going to need the Demco Air Force One Flat Tow Brake System for…

view full answer...