Baby Moon Hubcaps For a 15" Conventional Trailer Wheel With a 10-3/8" Center Ring Diameter

Question

Question:

First of all how do I return them to you and second how do I get the ones that I need I’m gonna send some pictures with the wheels and the measurements I hope this helps thank you so much I thought I was right I wasn’t even close lol Thanks again for all your help in advance

asked by: John H

1

Helpful Expert Reply:

Based on the measurements of your wheel you included it appears you will need the Phoenix USA Baby Moon Hubcap # PX1307SS. This hubcap has an outer diameter of 10-1/2" with an inner diameter of 10-3/8" and a lip that is 10-3/16" across.

For the return you will need to contact our customer service team at 1-800-298-1624 to get a return authorization to mail them back. Once the item is returned and inspected any refund will be issued. In the mean time you can place the order online for the new hubcaps.

expert reply by: Bud M

1

Conventional 15" Wheel Radius
(click to enlarge)

Conventional 15" Wheel Diameter
(click to enlarge)

Answer 1

The wheel used on the #AM32395 Karrier 205/75-15 wheel doesn't have the retention clips or nubs stamped into it that would hold a hubcap in place (see photo). I have some options for you though. A conventional steel wheel like what's provided…

view full answer...

Answer 2

If the outside of the mounting tabs for a baby moon cover on your wheel measures 10-1/4 inches then the Baby Moon Cover part #AM981306 will fit and work well. These have an inner diameter of 10-1/4 inches. Normally these will only fit 6 lub wheels so…

view full answer...

Answer 3

It sounds like you are looking to replace the rubber grip or "latch handle grip" on your door latch handle. We do carry the Replacement Rubber Grip #FVH200. This is a 3" long section will fit a on the end of a 2" wide 1/4"…

view full answer...

Answer 4

Thanks for the pictures Dalen. The Phoenix USA Baby Moon Hubcap, you were looking at will only work with 6 lug wheels so it's not going to work with your 5 lug wheels. I do not think your wheel has a large enough lip but regardless we do not have…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Baby Moon Hubcaps For a 15" Conventional Trailer Wheel With a 10-3/8" Center Ring Diameter

Product Page this Question was Asked From

Continue Researching