Replacement Power Gear Control Panel For a 1996 Fleetwood Discovery

Question

Question:

Will this work on my 1996 FLEETWOOD DISCOVERY?

asked by: Shawn M

0

Expert Reply:

I believe you will need the Replacement Lippert Power Gear Manual Leveling Control Kit # LC359259 for your 1996 Fleetwood Discovery. You will need to remove the control panel to determine if you have the old style wiring connection or the new style which connects to the Replacement Key Pad # LC82FR you found.

expert reply by: Bud M

0

Answer 1

Are you only installing the #LC82FR (500731)? To replace your 500210 you will need the full kit #LC359259. There are also wiring changes you will have to make at the pump assembly before it will work. After speaking with Lippert it sounds like this…

view full answer...

Answer 2

I found an old wiring diagram for your now discontinued Power Gear 500210 control panel and it really helps show how things are supposed to work. There is a red wire running to the three jacks, the dump valve, and the float valve from the solenoid.…

view full answer...

Answer 3

That could definitely be your issue. You will want to trace that power wire to see if it is a wire issue or if it is a control issue. Use circuit tester #PTW2992 to test for power going into and out of each component. If it is a wire short circuit,…

view full answer...

Answer 4

I believe you meant to type that your touch pad was part number 500210 which the Replacement Key Pad Control Unit for Power Gear Powered RV Leveling System #LC82FR is a correct replacement for.

view full answer...

Answer 5

Yes, The Replacement Key Pad Control Unit for Power Gear Powered RV Leveling System #LC82FR is the correct key pad control unit you will need per Lippert for your 1998 Chevy Southwind Storm Motorhome using the 500210 Milwaukee cylinder board. I…

view full answer...

Answer 6

Sounds like the control panel was fried when the dealer messed up the wiring. Only solution will be an all new control panel with the part #LC359259 which we have confirmed fits the now discontinued Power Gear 500210 leveling system.

view full answer...

Answer 7

Hey John, your Coleman likely has been pre-wired with a Furrion inlet like #FSPINS-BS in which you can use the Go Power Overlander Solar Charging System with Digital Solar Controller #34282181 which would utilize the pre-wire port and get mounted to…

view full answer...

Answer 8

For your Glo-Brite 118A amber light the replacement lens that will fit is the Optronics #A44AB; the lights themselves are the Optronics #MC44AB. The Glo-Brite 117R can use replacement lens #A44RB while the light is #MC44RB. I've added links to…

view full answer...

Answer 9

Since Glo-Brite is no longer in business we can not get replacement parts for their products, that being said, the Lens for Optronics MCL0028 Series Clearance or Side Marker Light #A0028AB you reference is the closest replacement we offer. This…

view full answer...

Answer 10

Hey Keith! I did some research it and does look like you have the older Power Gear control board meaning you will need to change the wiring that used to be used for power and ground that side of the solenoid. I've attached a wiring diagram for…

view full answer...

Answer 11

Yes, since you already have a 6-way trailer connector installed that has some of its connection made, just those for basic trailer lighting, you need only to make the two additional connections for the output circuit from a trailer brake controller…

view full answer...

Answer 12

To answer your first question, it is possible to splice the brake controller's 12 volt power wire into the 12 volt power wire you have attached to the vehicle's battery to charge the trailer's battery but this is certainly not recommend.…

view full answer...

Replacement Power Gear Control Panel For a 1996 Fleetwood Discovery

Continue Researching