Can the Strap from the Erickson ATV E-Track Tie-Down Kit Be Purchased Separate

Question

Question:

I would like to just purchase the straps? Not the kit. Do you have a part # for the straps?

asked by: Connie M

0

Expert Reply:

Yes, we do offer the straps from the Erickson ATV E-Track Tie-Down Kit separately. I have listed these for you below, they vary by length.

12' - part # EM59136
16' - part # EM59139
20' - part # EM59140

expert reply by: Conner L

0

Answer 1

Erickson does offer a zinc-plated steel backing plate for use with their E-Track products like their ATV E-Track Tie-Down Kit #EM09160. Use part #e96RR. You can see this item's hole dimensions and spacing in the linked photo. Since your trailer…

view full answer...

Answer 2

It looks like each chock and strap from 2 of #EM09160 will need to be able to hold around 375 pounds to handle the weight of the 2014 Arctic Cat Wildcat X Limited and that is just static load and does not include the forces applied to the chocks and…

view full answer...

Answer 3

Hey Carl, if you used just the 4 bolts per backing plate of the etrailer E-Track Backing Plates w/ Hardware #e66RR with the Erickson ATV E Track Tie-Down Kit w/ Ratchet Straps and Wheel Chocks #EM98CV you would be fine. If you wanted to get more and…

view full answer...

Answer 4

Hello Benton, thanks for reaching out. Yes, the #DX64HR Hub and Drum assembly can be used for an axle that is set up for grease. You would just want to replace the oil cap with a grease cap like part #K7CAP and you will be good to go.

view full answer...

Answer 5

Thanks for reaching out, Tom! I recommend picking up some of the 4' sections of etrailer Horizontal E Track #e85VR and securing them to your wood floor with the etrailer E-Track Backing Plates w/ Hardware #e66RR. Then you can use the Erickson ATV…

view full answer...

Answer 6

Hey Todd, welcome back. If you don't want to install an e Track system then the SpeedStraps HD Through the Wheel Lasso Tie-Down Kit w/ Snap Hook item #SS29FJ would be a great option. These 2" straps have a 3,333 lb safe working load limit, a…

view full answer...

Answer 7

I do have an option for you but we don't carry any braking assemblies that are 10" diameter x 1-3/4" wide. These are an oddball size and would be best replaced with something more modern so you can access replacement parts if needed.…

view full answer...

Answer 8

We do have a direct replacement for your Kwikee Steps 1800709 controller - this is found as the Replacement Control Unit for Kwikee 38 Series Electric RV Steps #LC363989 on our site. Our part numbers may differ from the manufacturers but I've…

view full answer...

Answer 9

Since the slot dimensions and capacity of different brands of E-Track are identical, really the only differences are the finish and the lengths the tracks are sold in. If you're using the E-Track in an area where aesthetics are important, you can…

view full answer...

Answer 10

To install the etrailer Horizontal E-Track #e42VR to the floor of your trailer you need the E-Track Backing Plates w Hardware #e76YR which can be used to install the tracks on flooring up to 2" thick. If your trailer floor is thicker than that…

view full answer...

Answer 11

If the Erickson ATV E-Track Tie-Down Kit w/ Ratchet Straps and Wheel Chocks #EM98CV are all coming loose, there is definitely something odd going on. First thing you will need to check is the release levers. You will need to make sure they are not…

view full answer...

Answer 12

The working load limit for the E-Track system like the part #E19148 that you referenced is 2,000 lbs. There isn't a set method required for tightening a load to the E-Track. Basically you would want to use a properly rated strap for the weight of…

view full answer...

Can the Strap from the Erickson ATV E-Track Tie-Down Kit Be Purchased Separate

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching