Erickson E-Track Strap with Ratchet - 2" Wide x 12' Long - 1,165 lbs

Ask the Experts about this Erickson E Track

• Recommended Tie Down Straps for BoxLink System on 2015 Ford F-150
  With the BoxLink system on your 2015 Ford F-150, you have multiple options when it comes to tie down straps. You can attach directly to the BoxLink cleats or hook directly to the interface plate with a bungee cord, S-hook, or E-track fitting. I have attached a link to multiple options for tie downs. A couple popular options are the Erickson E-Track Strap with Ratchet, # EM59136, and Erickson Re-Tractable Ratchet Straps, # EM34415.
  view full answer...
• Mounting Suggestion For E-track To Aluminum Utility Trailer
  For your Aluma 6810 HBT trailer, I recommend the Erickson Horizontal E-Track - Zinc Coated Steel - 2,000 lbs - 5' Long - Qty 1 # E19148 along with the E-Track Backing Plate - Zinc Plated Steel - 6-1/2" Long x 6" Wide # BPEZ. This will save you the expense of the dual track and will allow you the flexibility of plates between the braces or around them. This track also comes in 4 foot # EM19147, and 2 foot # EM59150. I recommend using the E-Track Plastic End Cap # ET8730 to finish your...
  view full answer...
• Are the Erickson Horizontal E-Tracks Strong Enough for a 5,000 lb Vehicle
  Yes, the Erickson Horizontal E-Track part # E19148 will be plenty strong enough to secure your two rock crawler buggies. The tracks are each rated at 6,000 lbs max break strength and 2,000 working load limit. I assume you would have a track under each wheel so these figures would then be doubled. With that in mind, the weight capacity of these tracks in is regards to pull strength. The full weight of the vehicle should never be directly pulling on the tracks unless you were to hang them...
  view full answer...
• What Does Working Load Limit Mean for E-Track
  Good question and the 2,000 lb working load limit (WLL) of the Erickson Horizontal E-Track such as the 5 foot # E19148 is the safe limit for the weight of the cargo the track is helping secure. To simplify, it is the cargo capacity that the track can safely handle so you do not want to exceed it. However, the 2,000 lb limit is per track, so that means if you put down two tracks horizontally, your WLL would go up to 4,000 lbs. This track cannot actually be welded on, it needs to be secured...
  view full answer...
• Best Versatile Tie-Down Options for a Cargo Trailer
  I am not sure how many of the Erickson E-Track systems you have seen but it really is your best bet when it comes to versatility and functionality. Not only do they have the Horizontal E-Track, like part # E19148, but they also have Vertical E-Track like part # E19146. You could install both types of track on your cargo trailer (if it is enclosed) and then move the attachment points around by either using the Erickson E-Track Strap # EM59136 or using the Tie-Off w/ D-Ring # E59143 along...
  view full answer...
• E-Track Recommendation for Securing ATV to Utility Trailer
  E-track can easily attach to the wood floor you have in your open utility trailer. This is a very common style of trailer that is used with the E-tracks. I attached a couple review videos that show etracks installed in a similar trailer as yours and what they use to secure the cargo. The etrack sections like the part # E19148 would be more than adequate to secure your ATV. The # 59131 is a great anchor to use, or if you want a strap that attaches directly to the etrack we have the...
  view full answer...
• Enclosed Trailer Wall Reinforcement for Installing Erickson E-Track
  To install an 8-foot length of Erickson E-Track # E19135 inside your enclosed trailer I do recommend first mounting some plywood to your interior wall studs. A piece of plywood that is larger than the E-Track's 5-1/8-inch width will spread the load across more of the trailer structure. For instance if you first installed a 1 x 8-foot piece of plywood across the studs that would allow more fasteners to be used than with the E-Track rail alone. Then you could mount the E-Track to the...
  view full answer...
• Wall-Mount Cargo Control Products for Use Inside 7 X 12 Enclosed Trailer
  We offer a range of trailer cargo control products including the versatile Erickson E-Track # E19146 for vertical applications that you referenced. These can be used with any of the E-Track strap products shown on the link at right, including the 12-foot ratcheting strap # EM59136. Other available accessories include spare tire mounts like # RA-16HST from RackEm.
  view full answer...
• Does the Erickson ATV E-Track Tie-Down Kit # EM09160 Have to be In-Line with Direction of Travel
  You can use the Erickson ATV E-Track Tie-Down Kit # EM09160 to help secure your ATV but you really need something securing your ATV in the direction of travel. You could put some Horizontal E-Track like part # E19148 in-line with the direction of travel and do a kind of criss-cross pattern over your ATV with straps like part # EM59136 to help secure it, but Erickson does not recommend securing the load only using a straps that are not with the direction of travel. As long as your...
  view full answer...
• Hardware Recommendation for Securing E Tracks to Plywood Trailer Floor
  Securing the Erickson E-Track # E19148 to 3/4 inch plywood should be sufficient. To secure the track to the plywood, you can use screws, or rivets. Using 1/2 inch screws would be a good length with 3/4 inch plywood. You will want to attach screws at least every other mounting hole. For tie downs and straps I would recommend either the E-Track Tie-Off Ring # 59131, or E-Track 2 inch D-Ring, part # E59143. Also available is the Erickson E-Track Strap with Ratchet, part # EM59136.
  view full answer...
• Chock and Strap Trailer Tie Down System For A 2016 Polaris RZR With 32" Wheels
  To secure an ATV with 32" tires to a trailer a few components are needed for worry-free transport. The Erickson Horizontal E-Track part # EM59150 is a great system for securing a variety of items, not just your RZR. For your specific need, a set of wheel chocks and tie downs like the Erickson E-Chock Wheel Chocks for E-Track part # EM09162-2 and the Erickson E-Track Strap with Ratchet # EM59136 are needed. In total you need 4 tracks, 2 wheel chock sets, and 4 tie down straps to secure...
  view full answer...
• Mounting E-Track for Hauling Motorcycle on 8 x 5 Trailer
  That's a great question. I believe your installation method for the Erickson Horizontal E-Track # EM59150 sounds like a great plan as long as you have the tracks facing the direction of travel. Basically the E-Track was designed around this and that is the most safe way to secure cargo. To secure your 900 lb bike you can either use the Erickson E-Track Tie-Off w/ D-Ring # E59143 with your current ratchet straps or you can update to the Erickson E-Track Strap with Ratchet # EM59136 which...
  view full answer...
• Erickson E-Track Straps for Enclosed Trailer Transporting ATV
  If you already have four E-Tracks mounted to the floor of your enclosed trailer and you wish to secure your ATV with only straps, not wheel chocks too, you certainly can do this. But instead of using the strap-and-chock kit # EM09160 you can use one of the E-Track strap-only items shown on the linked page, such as 2-inch x 12-foot ratchet strap # EM59136 which is rated for a working load limit (WLL) of 1165-lbs. We also have longer ratchet straps like the 16-foot # EM59139 with the same...
  view full answer...
• E-Track Cargo Control Options for Installing Shelving in 18-Foot Enclosed Trailer
  We can help you with an E-Track cargo solution to allow installation of shelving on one side of your 18-foot enclosed trailer. Rather than use ceiling- and floor-mounted tracks I suggest you consider using Erickson's Vertical E-Track # E19146 along with their E-Track Wood Beam Socket # 59149 on one interior wall. You will supply and install standard 2 x 4 lumber and hardware to create the horizontal portions of the shelving using the 2 x 4s.. The advantages of this method are reduced...
  view full answer...
• Using The E-Track Trailer Cargo Control # EM59150 On Trailer To Secure ATVs and Motorcycles
  Installing the E-Track Trailer Cargo Control, part # EM59150, would work well to strap down your ATVs and motorcycles on your V-nose trailer. You could mount the E-Track sideways or perpendicular to the trailer frame over the floor as you described. The E-Track can also be mounted on the wall of trailers, so perhaps you could mount the track for the ATVs on the floor towards the front of the trailer. Then you could mount track on the trailer walls for the motorcycles or on the floor...
  view full answer...
• Recommendations for Securing Marching Band Equipment in Enclosed Trailer
  Instead of securing your marching band equipment from the floor you could secure it from the wall using the Erickson Vertical E-Track # E19146. You can then use the Erickson E-Track Tie-Off w/ D-Ring # E59143 to provide tie-down attachment points or use a tie-down like the Erickson E-Track Strap with Ratchet # EM59136 that installs directly into the E-Track .I have also attached a link to our selection of accessories that are compatible with the E-Tracks that you can filter through. An...
  view full answer...
• Cargo Tie-Down System To Secure Speaker Equipment In Haulmark Enclosed Trailer
  We have a couple different styles of E-Track systems. We offer a 5-foot track system like part # E19148 that has horizontal slots and usually installed on the floor or the inside of the walls in an enclosed trailer. We also offer a vertical E-track part # E19146 that is four feet long and used the same way. You will want to know which way you want the slots in the track to run for securing your band equipment. One great way to use different type tie-downs with the E-Track system...
  view full answer...
• Mounting E-Tracks in Enclosed Trailer
  There needs to be some type of strong structural component on your trailer where you want to mount the Erickson Horizontal E-Track # EM59150. There is nothing that I can recommend which will ensure they will be strong enough unless your trailer has the proper place to mount the tracks. You may want to consider putting the E-track on the floor and then using Erickson E-Chock Wheel Chock for E-Track # EM09162 and ratcheting straps such as # EM59136.
  view full answer...
• Equipment Needed to Secure a 2003 Honda VTX 1800R for Travel
  The B&W Biker Bar systems that use the base # BWMC2300 you referenced are exclusively designed for Harley Motorcycles as of June 2018. We do have other options that you can use to secure your 2003 Honda VTX 1800R though. If you installed the MaxxTow Adjustable, Self-Locking Wheel Chock # MT70271 which fits tire widths from 3" - 5" and wheel diameters from 15" - 22" you could then secure your bike with the Erickson E-Track Strap # EM59136 and E-Track # E19148.
  view full answer...
• Pack Em or Erickson Wheel Strap Recommendation for Securing 2014 Honda Pioneer 700
  Actually both the Pack'em Wheel Ratchet Strap Kit part # PK-WTD and the Erickson Ratchet Strap kit part # EM09160 both use ratchet straps to secure the wheel. Since the Pack'em set is rated higher at 2,000 lbs that would be what I would recommend for you. For just the strap # EM59136 is for the Erickson setup.
  view full answer...
• Cargo Solutions for a 7 x 16-Foot Enclosed Trailer
  Erickson's E-Track Cargo Control systems offer excellent flexibility at a moderate cost. Their E-Tracks are offered in several lengths, such as a 5-foot # E19148 for horizontal applications. Many types of accessories are offered as well, including tie-off rings like # 59131, D-rings like # E59143 and ratchet straps like # EM59136. I have included links for both E-Track items as well as some interior trailer cargo control items.
  view full answer...
• E-Track Ratchet Straps to Secure Various Diameter Pipes in an Enclosed Cargo Trailer
  The Erickson ratchet strap # EM59136 would be a good option. This strap is 12 feet long and 2 inches wide. I have linked a video review for you to check out to the right. There is also an 8 foot version, # SLLS28RER, 16 foot version, # EM59139, and 20 foot version, # EM59140. What I would do is ratchet strap each bundle with a regular ratchet strap such as # EM34420. Then I would secure them against the trailer using the E-track and E-Track ratchet straps.
  view full answer...
• Using Erickson Roller Idler Along with E-Track Tie Down Ring
  The Erickson E-Track Tie Down Ring # 59147 that you mentioned will work very nicely along with the Erickson Roller Idler # EM09144. This tie down ring has a Safe Working Load Limit of 2,000 pounds and a 6,000 pound capacity. As you referenced in your question, when using this with the Roller Idler that will act as an anchor point, the strap will then be fed through the ratchet and run more parallel to the E-track. This will not affect the weight capacity of the Tie Down Ring. I confirmed...
  view full answer...
• Can the Ratchet Straps Which Come With the Erickson ATV E-Track Tie-Down Kit Be Ordered Separate
  If you are looking for just the e-track mount ratchet straps which comes with the Erickson ATV E-Track Tie-Down Kit part # EM09160 the closest thing we have is the Erickson E-Track Strap with Ratchet part # EM59136 which is just a slightly longer version.
  view full answer...
• E-Track and D-Ring Recommendation for Securing Cargo in Enclosed Trailer
  I'd install e-track on the walls of the trailer so that you could use e-track tie down anchors like part # 59131 and/or e-track ratchet straps like part # EM59136. The e-tracks give you tons of flexibility in how to strap everything down since the anchors can easily be moved as needed. For e-track then you can use the Vertical E-Track # E19146 mounted throughout your trailer using self-tapping screws. I attached an install video on how to install the tracks as well.
  view full answer...
• Using Erickson Horizontal E-Track for Securing 2 Sport Quads on 12 Foot Trailer
  E-track is very versatile and comes in different lengths so you can choose what best fits your needs. If you plan on using the e-track to only tie-down your sport quads, it can work well to have the e-track in the middle of the trailer for a tie-down point. However, it you think you will use the e-track to transport other cargo and will need more tie-down options, using 2 rows of e-track will work better. I spoke with one of my co-workers and he says he uses a single row of e-track to...
  view full answer...
• Ratcheting Strap that Retracts But as an E-Track Mounting End
  I do have a couple of options for you for the etrack mounting. We have the CargoBuckle G3 Retractable Ratchet Straps w/ E-Track Adapters - 2" x 6' - 833 lbs - Qty 2 # IMF18800-87 and the CargoBuckle Mini G3 Retractable Ratchet Straps w E-Track Adapters - 1"x6' - 466 lbs - Qty 2 # IMF103745-87. Another option is to use the ratcheting strap you want, # EM34416, and then use an E-Track tie off ring # 59131 and hook onto it with one end of the strap. Another option is a strap like #...
  view full answer...

Do you have a question about this E Track?