Sway Control For 2022 VW Atlas That Cant Use Weight Distribution

Question

Question:

Have a 2022 VW Atlas V6 and a 2022 Jayco Jay Flight SLX 7 SDX 184BS. GVWR is 4500lbs. The dealer sold us an Equalizer weight distribution hitch with sway control. Just read that VW says to never install weight distributing or load equalizing ball mounts. Also using Curt Echo Mobile Trailer brake. What are our options to be able to safely tow within VW guidelines and achieve the same result as a weight distribution hitch with sway control to stay safe on the road without voiding our vehicle warranty?

asked by: Melissa

0

Expert Reply:

While there isn't a way to completely mimic how a weight distribution hitch works, you can use a friction sway control system for a safer way to tow with your 2022 VW Atlas, and you'll also need a bracket that goes over your ball mount:

- Reese Friction Sway Control Kit # 83660

- Reese Sway-Control Bracket for 2" Ball Mounts # RP26003

Then to help with any suspension sag, what you can do is add air springs to the coils, the Firestone Coil-Rite Air Helper Springs # F4175.

expert reply by: Kyle S

0

Answer 1

We do have the Curt Custom Wiring Adapter #C29JR which will allow you to use a Curt brake controller like the Assure #C49UR which is one of the better proportional controllers like your Tekonsha Prodigy wireless trailer brake controller. The…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 5

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 6

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 7

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 8

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 9

The differences between the Firestone Ride Rite #F2613 and the Red Label #F2709 for your 2023 GMC Sierra 3500 Crew Cab Long Bed is the air pressure and max weight capacity. The Ride-Rite #F2613 are rated for 5,000lbs and 100 PSI, where the Red Label…

view full answer...

Answer 10

Hey Kurt, yes the correct gap for SumoSprings Solo kits like the part #SS88UV is 1/2 inch to 1 inch like you mentioned. Did you install this already?

view full answer...

Sway Control For 2022 VW Atlas That Cant Use Weight Distribution

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching