Depth of Receiver for the Draw-Tite Hidden Hitch on a 2022 Ford Mustang Mach-E

Question

Question:

Hello, what is the usable depth of the 2x2 receiver?

asked by: Brian

1

Helpful Expert Reply:

The 2' x 2" receiver portion of the Hidden Hitch by Draw-Tite item # DT72GR has a 5" depth before you get to the weld. This is from the opening of the receiver to the farthest point on the inside. This hitch is a confirmed fit for the 2022 Ford Mustang Mach-E.

expert reply by: Jerred H

1

Answer 1

As we haven't had the chance to install either the Curt #C77ER or the Draw-Tite #DT92MR on a 2021 Mustang Mach-E, I went out and measured from the center of the first bolt hole to the end of the receiver opening on both hitches. The Curt will sit…

view full answer...

Answer 2

That's a good question, and there is one option I do like better for your 2021 Ford Mustang Mach-E between the Curt #C77ER and Draw-Tite #DT72GR hitches, and that's the hitch from Curt, which is the following part number: - Curt Trailer Hitch…

view full answer...

Answer 3

I can't say for sure since it hasn't been tested and we don't have one around to try it out. It would also depend on the actual bikes and bike rack you have. I imagine that as convenient as it may seem it is probably a horrible pain to…

view full answer...

Answer 4

Yes, you would want to use a 4-way mounting bracket like the part #18144 with the Hidden Hitch part #DT72GR to mount the 4-way of the Curt harness part #C59236 that is a fit for your 2022 Ford Mustang Mach-E. The hitch comes with a bracket for the…

view full answer...

Answer 5

I would be happy to compare those two hitches for you but there is little to no technical information available about the Stealthhitch because it does not release until the end of August 2022. Out of the two I would highly recommend the Draw-Tite…

view full answer...

Answer 6

That is a great question, and yes, the 200 lb TW rating is accurate. The Curt #C77ER is "technically" a class 3 hitch because it has a 2" receiver. The 200 lb TW rating and 2,000 lb towing weight is generally what you see on a class 1…

view full answer...

Answer 7

The Curt Class III trailer hitch #C13119 does have a 350-lb tongue weight (TW) rating as you noted, and that capacity must be enough for the weight of the bike rack itself plus that of your loaded bikes. A substantial 4-bike rack like the Hollywood…

view full answer...

Answer 8

The Curt Trailer Hitch Receiver #C77ER does protrude from the bumper. I spoke to a contact at Curt and he did not have the length the receiver came out from the bumper. We measured the hitch and from the first mounting hole to edge of the receiver is…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 12

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Depth of Receiver for the Draw-Tite Hidden Hitch on a 2022 Ford Mustang Mach-E

Continue Researching