Replacement Hardware Available For Lippert Coach Steps

Question

Question:

i can see on web that you have some parts for Coach Steps I am looking for the bolt that through the gear sku 164348. It mounts gear to step bracket.

asked by: Jim M

0

Expert Reply:

The Replacement Joint Assembly Hardware Kit # LC216567 is the only replacement hardware that Lippert offers for the Coach Steps. This hardware is for mounting the arms together on the steps. For the bolt that holds the gear on the steps you will need to locate that from a local hardware store.

expert reply by: Bud M

0

Answer 1

Thanks for all of that info, and for your Kwikee steps, the part number 902508000 means you have a 25 Series step, and the because the sixth digit is an "8" that means yours is a was built between early 1999, and late 2005 to early 2006.…

view full answer...

Answer 2

I reached out to my contact at Lippert and he did verify that the Replacement Motor #LC369506 you purchased will not work with your existing Kwikee Triple Step assembly and unfortunately there's not a separate component that will allow it to fit.…

view full answer...

Answer 3

Hey William, yes you can definitely replace your 25 Series Kwikee steps part #LC369552 with a 32 Series part #LC3722616 and this would allow to go from a 3 step to a 2 step setup. The mounting brackets are exact same so the install will be very easy…

view full answer...

Answer 4

When the 909508000 part number has come up before it has been in relation to Kwikee 40 Series Steps which use the Replacement Control Unit for Kwikee 40 Series Electric RV Steps #LC363985. Unfortunately your motorhome information doesn't actually…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 11

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Replacement Hardware Available For Lippert Coach Steps

Product Page this Question was Asked From

Continue Researching