Replacement Brake Shoes For 4,400 lb Dexter Manual Adjust Electric Brakes

Question

Question:

Can these be used on manual adjust brake assemblies? K71-699-00 I have a Dexter 4400# axle and the bake shoes are Dexter part number K71-672-00.

asked by: Jerry

0

Expert Reply:

The part number you mentioned will not, but we do have exactly what you need, which are replacement brake shoes and linings for your manual adjust Dexter 4,400 lb electric brakes. The correct part - which fits both the left and right hand side brake assembly - is the following:

- Replacement 10" x 2-1/4" Electric Brake Shoes # BP04-095

expert reply by: Kyle S

0

Answer 1

From what I have found, you have 10" x 2-1/4" 4,400 lb Dexter brake assemblies. For replacement shoes you need the Replacement 10" x 2-1/4" Electric Brake Shoes - 1 Brake Assembly #BP04-095 which works for left hand and right hand…

view full answer...

Answer 2

By the time you add up the cost to replace the magnets and shoes on your trailer you are at the cost (or more) for all new assemblies plus you end up saving yourself the trouble of messing with trying to install all the components. For an exact…

view full answer...

Answer 3

I can certainly help you find the replacement brake shoe and brake magnets for your Dexter brake assemblies on your 2014 Forest River. We have different part numbers for the replacement parts you listed, but they are the correct parts for your brake…

view full answer...

Answer 4

The 10" x 2-1/4" Electric Brake Shoe/Lining (One Wheel) #BP04-095 are the brake shoes for the Dexter electric brakes and they will fit the Axletek brand just fine. The #AKBRKR-S-10 are also a fit for your 4,400 lb axles.

view full answer...

Answer 5

Keith, it appears so - but to be sure I'd recommend just confirming that your current brakes are 10" x 2 1/4", has a 4 bolt mounting flange, and all of the specs listed on the product page matches. If all that checks out, then yes the…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Replacement Brake Shoes For 4,400 lb Dexter Manual Adjust Electric Brakes

Product Page this Question was Asked From

Continue Researching