Replacement for TU-750-2 RV Battery Power Converter and Battery Charger

Question

Question:

what is available to repace unit in 1989 dutchman rambler 120V 60HZ 8.6 AMP 12.0VDC50 AMPS TOTAL MAX NO BATTERYS POWER FROM 20 AMP PLUG

asked by: SEAN C

0

Expert Reply:

Since your current RV power converter/charger is a 50 amp setup you could use the Progressisve Dynamics Inteli-Power Converter part # PD9260C which is rated a little higher at 60 amps.

expert reply by: Jameson C

0

Answer 1

Hi Jeffrey, The equivalent of the Progressive Dynamics PD9360 that we carry is the Progressive Dynamics 9300 Series RV Converter Charger part #PD79RR. It's the same unit, different part number. This is a 60 amp converter charger designed to…

view full answer...

Answer 2

Hey Casey, thanks for reaching out! The 15,000 Btu Dometic Penguin II High Capacity RV Air Conditioner w/ Heat Pump is no longer available, unfortunately. You might be able to find it online elsewhere (if someone has it in stock) as 651916HXX1C0-01…

view full answer...

Answer 3

Hey Thomas, thanks for reaching out. You will definitely want to stick with a 30 amp when replacing your old 30 amp unit. For that I recommend the following: - Progressive Dynamics 9300 Series RV Converter Charger - 12V - 30A #PD49RR There would be…

view full answer...

Answer 4

The Go Power RV Converter and Smart Battery Charger - 12V - 55 Amp, part #34266169, will work. You might have to do some altering to make it fit.

view full answer...

Answer 5

Yes, the Progressive Dynamics Inteli-Power RV Converter and Smart Battery Charger, #PD9260C can be used to replace a 50-Amp charger model but you will need to ensure the wire from the charger to the battery bank is suffiently sized and update if…

view full answer...

Answer 6

Resetting the #FR33PR requires pulling the power from the thermostat. However, it is unlikely this will fix your error code. The E3 code means there is a loss of communication between the thermostat and control box. Double check your wires and make…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Replacement for TU-750-2 RV Battery Power Converter and Battery Charger

Continue Researching