Replacement Hardware Kit For A Curt # 13068 Trailer Hitch For A 2003 Honda Odyssey

Question

Question:

Do you have a replacement hardware kit for curt 13068?

asked by: Brian J

0

Expert Reply:

The Replacement Hardware Kit # RHK will give you the replacement hardware needed to install your Curt Hitch on your 2003 Honda Odyssey.

When you get to the # RHK web page there will be two boxes you will have to fill out. The first box you ask you what the hitch item number is type in C13068.

The second box will ask for the manufacturer it is a drop down menu select Curt then place your order and it is all good to go.

I attached a review video link below.

expert reply by: Noah E

0

Answer 1

What you can do is use a bolt leader like #80101-1 with a carriage bolt block through an open portion of your frame to basically act as a weld nut so you can install the hitch. This normally is a solution we use when a vehicle has a broken weld nut…

view full answer...

Answer 2

Hey Brian, To get a replacement hardware kit for your Curt Trailer Hitch Receiver #C23WR you'll need to go to the #RHK page and enter in your hitch part number (C23WR - our number for 13486) into the box above the add to cart button.

view full answer...

Answer 3

The center to center spacing between the mounting holes in the Replacement Hardware Kit for Curt SecureLatch Pintle Mount #C52CR are 1-3/4".

view full answer...

Answer 4

The bolts included with the Draw-Tite Class III #75471 Hitch are Class 10.9. They're 10mm in diameter, 30mm long and have a 1.25 thread pitch. If you're needing replacement installation hardware, we can supply a replacement hardware kit for…

view full answer...

Answer 5

Hey Cory, If you can access an open end of the frame where the weld nut broke off you could fishwire a new carriage bolt in place of the weldnut. Otherwise you may have to weld the hitch on. You would need 1/2 inch diameter fishwire like part…

view full answer...

Answer 6

If you can access an open end of the frame where the weld nut broke off you could fishwire a new carriage bolt in place of the weldnut. Otherwise you may have to weld the hitch on. Looking at the install instructions for the hitches for your 2012…

view full answer...

Answer 7

The Replacement Hardware Kit for Curt SecureLatch Pintle Mount #C52CR is 1/2" coarse thread, and measures 2-3/16" long overall, with the threads measuring 2-5/8" long.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 11

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 12

Hey Adrian! The higher capacity for the B&W #BW47BR and Curt #C77MJ comes from the construction. The B&W hitch weighs 45 lbs and then the Curt and Trailer Mate #TMT54FR both weigh 32 lbs. The Trailer Mate does sit just a tad higher compared…

view full answer...

Replacement Hardware Kit For A Curt # 13068 Trailer Hitch For A 2003 Honda Odyssey

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching