Replacement Lead and Follow Legs for Venture VMC900

Question

Question:

Hi I need to replace my landing bear legs on my 5th wheel. The numbers of the caps are vmc900r-329581 and Vmc900L-319820. Can you help me out in figuring out which legs I need?

asked by: James M

0

Expert Reply:

I would be happy to help you find replacement legs for your 5th wheel. You are going to want the Replacement Lead Leg item # LC119102 which will work well as a replacement for your Venture VMC900. Then for the matching follow leg you are going to want the Replacement Follow Leg for Venture Landing Gear item # LC119101.

expert reply by: Jerred H

0

Answer 1

Since your Venture leg is the follow leg the repair kit is #LC146060. If you had the lead leg it would be #LC146059.

view full answer...

Answer 2

The only follow leg I can recommend you use with your Venture landing gear would be the part #LC179014. Stromberg Carlson makes the Venture landing gear, that is the brands are different but the jacks are the same. I cannot recommend you install a…

view full answer...

Answer 3

I have a few different options for you depending on the route you would like to take. However, regardless of which route you pursue you will need to take some measurements of your outer jack tube length and weld stop spacing. If you are handy and the…

view full answer...

Answer 4

Hey Bob, Landing gear components aren't all interchangeable between brands so I'd need to know the exact model to find replacement parts for your current system. If you're just wanting to replace the landing gear as a whole then I'll…

view full answer...

Answer 5

When you are looking for replacement landing gear the 2 big things to take into consideration are the weight of your trailer and the weld stop locations on your current setup. Since the GVWR of your 2004 Cougar is 10,300 lbs our Landing Gear Set w/…

view full answer...

Answer 6

There are a few things that go into making sure you choose the correct replacement landing gear. First you need to be sure that the landing gear is rated properly. If you check out the weight rating on your current landing gear just make sure the…

view full answer...

Answer 7

The gearbox #RVLG-RDBOX for the Landing Gear Set w/ Handle #RVLG-8HDL can be mounted in the horizontal or vertical position. I went out to the warehouse and tested both the gearbox and lead leg together and the pins that hold the gearbox in place…

view full answer...

Answer 8

The only difference between the #RVLG-8HDL and the #RVLG-8000 is that the #RVLG-8HDL includes the manual crank handle, while the #RVLG-8000 doesn't. The dimensions for both are the same. • Retracted Height of 32-3/4 inches • Extended Height of…

view full answer...

Answer 9

You can use the RV Propane Gas Detector #RS64FR (white) or #RS44FR (black) to replace your current Atwood 31013 propane gas detector. This will also use a 12v, 2-wire installation like your current detector.

view full answer...

Answer 10

The only difference between the Replacement Crank Handle for etrailer and Ram 5th Wheel Landing Gear #RVLG-8HDL that you mentioned, and the Landing Gear Set #RVLG-8000 is that #RVLG-8HDL comes with the handle, whereas if you were to go with…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Hello Sam; that is a great question! I reached out to Furrion and you will be able to use the Furrion Chill Cube #FR69TD (white) or #FR49TD (black) with your furnace. However, the remote is not capable of operating the furnace at this time. Also, we…

view full answer...

Replacement Lead and Follow Legs for Venture VMC900

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching