Availability of a 2,000LB Trailer Axle With 60" Spring Center

Question

Question:

do you have any with 60in spring center?

asked by: Brian

0

Expert Reply:

The Trailer Axle with Idler Hubs # e32GR is the closest we have to a 60" spring center for a 2,000lb trailer axle. These have a spring center of 58" with a hub face length of 72". It includes idler hubs with a 5 on 4-1/2" bolt pattern. You can have new Spring Seats # TRSS175 welded to the axle in the 60" spring center you need. The axle requires a minimal overhang of 11-1/2" which you would have 12" with a 60" spring center and 72" hub face measurement.

expert reply by: Bud M

0

Answer 1

Since you want to change your trailer hubs to the 5-on-4-1/2 bolt pattern I suggest you select a 60-inch axle kit that includes idler hubs, such as one of the two kits shown on the linked page. These two 2K-rated axle kits include 5-on-4-1/2 hubs,…

view full answer...

Answer 2

Welcome back! The correct U-Bolt kit for mounting your 2,000 lbs trailer axle is item #APUBR-10. The right set of leaf springs for your trailer is typically determined by capacity and where your spring hangers are mounted. Since you are customizing…

view full answer...

Answer 3

The parts and quantities do look mostly good, but you would only need one of the hanger kits #APS2. These are actually sold as a full kit for one axle. As to said axle, though, it would be a good idea to double check that your spring seats match the…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

Hey Nate, We do not have a 3/4" spindle nut or washer, the smallest option is the 7/8" spindle nut #165931and a 1" washer #SW1000. I cannot find anything smaller. Are you sure the threads on you're spindle are 3/4"? If they…

view full answer...

Answer 6

In order to determine if we have an axle that would bolt right up to what you have without welding we need to know the distance between your spring seats on center. We also need to know hub face to hub face dimension of your current axle as well.

view full answer...

Answer 7

I did some research and found that the Erickson O-Track Cargo Control System like part #EM59133 is very similar to the L-Track systems you referenced. The Erickson O-Track is 18 inches long and includes 2 Spring-loaded O-ring clips and mounting…

view full answer...

Answer 8

You can add larger wheels and tires to a trailer as long as you have enough room for the larger size. The main clearance issues we find when putting larger tires and wheels on a trailer is from the top of the tire to the fender and from the inside…

view full answer...

Answer 9

To measure the width of a trailer wheel you will measure from where the tire beads will seat on the wheel. That will be from the inside of the inner wheel flange to the inside of the outer wheel flange, not from edge to edge of the wheel. To measure…

view full answer...

Answer 10

Hi Bryan! The hub included with the CE Smith Trailer Axle w/ Idler Hubs - 5 on 4-1/2 - 57-1/2" Long - 1.8K #CE33201GA-HUB is designed to fit 13 to 15 inch wheels and has too large of a diameter for 12 inch wheels. With you having 12 inch wheels,…

view full answer...

Answer 11

You can but it's going to stick out an extra 1-1/2" wide on either side and you'll need to move the spring seats and replace them with a pair of item #TRSS175. I checked our inventory and the etrailer Axle item #e37YR you were looking at…

view full answer...

Availability of a 2,000LB Trailer Axle With 60" Spring Center

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching