Undercover Access Hole Cover for EcoHitch Stealth Trailer Hitch Receiver Template

Question

Question:

Where can I find the cutting template for 2018 Tesla Model 3 for this cover? Undercover Access Hole Cover for EcoHitch Stealth Trailer Hitch Receiver 306-XA2002

asked by: Jonas M

0

Expert Reply:

For the EcoHitch Access Hole Cover # 306-XA2002 here are the instructions on how and where to drill access hole:

Place the bumper on the ground to allow marking on the inside floor of the plastic undercover with ribs.

Measure from the front of the plastic 26-3/4 inches along the center rib, if using a 3-1/2 inch hole saw. More hand clearance is possible if using a 4-inch hole saw but measure 26-1/2 inches.

Mark two points to use as start holes. Mark 3/4 inch from the center towards the driver side and 2-1/4 inches towards the passenger side.

Drill the two points using your hole saw.

Trim the excess plastic between the two holes to form an oval.

expert reply by: Jameson C

0

Answer 1

The trailer hitch options for a 2020 Chevrolet Bolt EV all require minor trimming of an underbody fascia panel. That said, this won't even be visible from outside the vehicle. The Curt Trailer Hitch Receiver part #C11457 however does require the…

view full answer...

Answer 2

Hey Leonard, thanks for reaching out! The cutout you need to make for the EcoHitch Hidden Trailer Hitch Receiver #306-X7359 on your 2023 Chevy Bolt EV is actually pretty simple, and you can see it at the 11:12 minute mark in the attached video. I…

view full answer...

Answer 3

In the install instructions for the Curt hitch part #C13420 there is a diagram that shows exactly how to measure to make the correct fascia trimming but it does not come with a template so that was a poor choice of words by the installer in the…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 8

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Undercover Access Hole Cover for EcoHitch Stealth Trailer Hitch Receiver Template

Product Page this Question was Asked From

Continue Researching