Center Cap Options For 15 Inch Aluminum Liger Trailer Wheel

Question

Question:

I purchased the Aluminum Liger Trailer Wheel - 15 x 6 Rim - 6 on 5-1/2 - Black and wanted to see what are my center cap options?

asked by: Elvi

0

Expert Reply:

Thanks for the purchase, and you have a pair of options that will fit the Aluminum Liger Trailer Wheel - 15" x 6" Rim - 6 on 5-1/2 - Black # LH49FR:

- Lionshead Trailer Wheel Center Cap w/ Snap-In Plug - 4.25" Pilot - Stainless Steel # LHCS108-SI60C

- Replacement Center Cap for 15" or 16" Aluminum Viking Series Wheels - Gloss Black # CXF104B

Both of these will fit the wheel, and it really just comes down to what style you prefer to go with your wheel.

expert reply by: Kyle S

0

Answer 1

We have two center caps that will work with a Lionshead Liger 15" rims. I have listed them below: Lionshead Trailer Wheel Center Cap w/ Snap-In Plug - 4.25" Pilot - Stainless Steel item #LHCS108-SI60C Replacement Center Cap for 15" or…

view full answer...

Answer 2

The Aluminum Liger Trailer Wheel #LH39FR has a 4.88" pilot diameter. This means the correct cap is the Lionshead Trailer Wheel Center Cap #LHCS109-SI60C.

view full answer...

Answer 3

Trailer wheel lug nuts that are 1/2-inch inside diameter typically have a 20-TPI thread pitch (20 threads per inch). Most lug nuts also use a 60-degree-coned profile like #CE11051, but a 90-degree like #STN569 is also available for 9/16-inch studs.…

view full answer...

Answer 4

Yes, as long as your wheel features a 3.19" diameter pilot hole the Taskmaster Center Cap #CXF106B that you referenced will fit and work well. Its style compliments their Viking Series aluminum trailer wheels really well, which is why it's…

view full answer...

Answer 5

The Titan Zinc-Plated, Leverlock Coupler - Adjustable Ball - 3" Channel - Bolt On - 5,000 lbs #T4845000 has a height with the lever up of 4-3/4 inches and 5-3/4 inches to the lowest part when that lever is up. I've attached a photo to…

view full answer...

Answer 6

To adjust the hitch latch on your trailer's coupler, you will want to adjust the nut at the bottom of the latch. This nut will be tightened or loosened depending on what you need for your coupler. I have attached a diagram showing you the…

view full answer...

Answer 7

Since you have 14 inch trailer wheel the studs of your hubs would be 1/2 inch which is a very common lug nut size. You don't actually have to switch lug nuts to go from steel to aluminum wheels though (or vice versa). Aluminum wheels have steel…

view full answer...

Answer 8

If you are absolutely sure that's your bolt pattern we don't have any spare wheels and tires that will fit, but we do know that the industry standard bolt pattern for 14 inch trailer wheels is 5 on 4-1/2 inch so most likely that is what you…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

The BTR and BT8 denotations refer to the spindle, not the trailer hub. The difference between a BTR and BT8 spindle is that the BTR spindle uses a 1.063" diameter L44649 bearing and the BT8 spindle uses a 0.99" diameter L44643 bearing. In…

view full answer...