What Size Bolt is Used to Hold On the Factory Bump Stops on a 2011 Ford F-150

Question

Question:

2011 F150 2x4 What size socket goes onto the jounce bumper bolt head?

asked by: Ernie

0

Expert Reply:

The bolt holding on the factory jounce bumper on the 2011 Ford F-150 is a 13mm. You will most likely need an extension to get to the bolt without interference from the jounce bumper.

expert reply by: Michael H

0

Answer 1

On many trailers the running light wires are jumped from one side to the other on the trailer. This is because there is a single running light wire only ran on one side. A wire would have to be spliced in on the one side, ran to the other side of the…

view full answer...

Answer 2

We used a 14mm socket to remove the jounce bumper on a 2014 and 2015 Ford F-150. The jounce bumper is about 4 inches long, so you will want to use an extension. I would use a 4 inch extension if you are using a standard socket and a 2 inch extension…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 10

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 11

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 12

Hello Dan, Great question. When you’re comparing the Firestone kits #F59VV and #F2582, they both technically fit your 2025 F-150, but they are designed around different mounting locations and truck configurations. The #F2582 is the traditional…

view full answer...

What Size Bolt is Used to Hold On the Factory Bump Stops on a 2011 Ford F-150

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching