Would Dutton Lainson Hand Winch DL14958 Work with Pontoon Boat Lift Winch

Question

Question:

I need to replace a Shelby 5353 pontoon boat lift winch. Your DL14958 says that it is for a trailer. Will it work on a boat lift?

asked by: Mark L

0

Expert Reply:

Yes the Dutton-Lainson Hand Winch w/ Automatic Brake # DL14958 would work great to replace the Shelby you have now on your boat lift winch.

expert reply by: Jameson C

0

Answer 1

We can help you with a winch but not with a large wheel like in the picture you mentioned. They have several winches designed for boat lifts and those winches are compatible with the big wheel you mentioned. These include the following: Heavy Duty…

view full answer...

Answer 2

As long as your winch is a Dutton Lainson B series winch, you can use the #DL6456 socket on it. The socket fits in 1/2" drill and measures 13/16" x 13/16" (outside). The number that you mentioned is just a number used to identify the…

view full answer...

Answer 3

The thread size on the DLB Series Brake Winch Ratcheting Replacement Handle #DL70347 is 5/8”-11.

view full answer...

Answer 4

Thom, based off of those measurements it does not look like the Replacement Friction Discs for Fulton Brake Winch #F501127 is going to work with your Shelby Industries 5353 winch. These pads are going to be a bit larger than what you have…

view full answer...

Answer 5

Yes, since the Dutton-Lainson Hand Winch w/ Automatic Brake #DL14958 has a brake that automatically sets when you release the handle it would work great for your pontoon boat hoist.

view full answer...

Answer 6

For your 1,500 lb boat and a boat lift, the winch I recommend is the Dutton-Lainson Hand Winch #DL14958. This will work perfectly with your boat lift, and I have added a photo a customer sent in of this winch being used on their boat lift. It has a…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Would Dutton Lainson Hand Winch DL14958 Work with Pontoon Boat Lift Winch

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching