Correct Replacement Braking Assemblies for Airstream International Signature 30

Question

Question:

What is the correct brake assemble for a 2016 Airstream International 30, Dexter Axle 410980-11 4500 lbs.

asked by: Gary C

0

Expert Reply:

It's likely you have a 4,400 lb axle which you can confirm by reading the sticker on the axle tag in the center of the beam. If that's the case then you will want to use the Dexter Nev-R-Adjust Electric Trailer Brake Kit part # K23-478-479. These are bolt-on assemblies which feature a simple four bolt pattern with two wire installation. They are standard 10" brakes.

expert reply by: Conner L

0

Answer 1

The correct hub and drum assembly replacement for your Lippert 4,400 lb axle is the #8-407-5UC3-EZ. This comes with bearings and a grease seal. If you need brakes as well you can use the #LC66WD, or for self-adjusting brakes #K23-478-479.

view full answer...

Answer 2

Hello Gilbert, thanks for reaching out. We do have brakes and hubs for Dexter 4,400 lb axles, but the sizing for these 4.4K axles can be funky depending when they were made. The best way to confirm what you need is with the casting number on the…

view full answer...

Answer 3

Your Dexter D44 Axle number 635096 uses the Trailer Hub and Drum Assembly #8-407-5UC3-EZ that comes preloaded with the Races #LM67010 and #L68111. It does include the Bearings #L68149 and #LM67048, Grease Seal #58846, Grease Cap #21-42-1 and lug…

view full answer...

Answer 4

Keith, it appears so - but to be sure I'd recommend just confirming that your current brakes are 10" x 2 1/4", has a 4 bolt mounting flange, and all of the specs listed on the product page matches. If all that checks out, then yes the…

view full answer...

Answer 5

Hey Mike, since your 2020 Grand Design Imagine 2600RB came with 4,400 lb Dexter axles the correct hub/drum replacement would be the part #8-407-5UC3-EZ and then for a set of left and right matching brake assemblies you'd need the part…

view full answer...

Answer 6

Hey Greg, what you have is the Dexter 4,400 lb trailer axle hub like the part #8-407-5UC3-EZ. This comes with the needed replacement bearings and seals but it is not pre-installed and greased like some options. Due to how rare this hub is there…

view full answer...

Answer 7

I currently have four different self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes. You can choose from the following: -Terran Axle Electric Trailer Brakes #TX97ZJ (3,500 Axles) -etrailer Electric Trailer…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

It's likely you have a 4,400 lb axle which you can confirm by reading the sticker on the axle tag in the center of the beam. If that's the case then you will want to use the Dexter Nev-R-Adjust Electric Trailer Brake Kit part #K23-478-479.…

view full answer...

Answer 11

The etrailer.com Electric Trailer Brake Kit #AKEBRK-7-SA and the Dexter Nev-R-Adjust Electric Brake Kit # 23-464-465 referenced in your question are both self-adjusting assemblies that will work to replace the existing Dexter brakes on your 7,000…

view full answer...

Correct Replacement Braking Assemblies for Airstream International Signature 30

Product Page this Question was Asked From

Continue Researching