Replacement Junction Box for Southland Trailer

Question

Question:

The cove for my 7 pin wiring kit on the southland trailer came off while driveing on the freeway. Is there a way to get a new cover

asked by: Dave B

0

Expert Reply:

I do have an option for you but the junction box lid's aren't universal so the only way to make sure you get a new one is to replace the entire junction box with one like the Trailer Wiring Junction Box part # 38656.

expert reply by: Conner L

0

Answer 1

On an 4 foot long section of E-track #EM19147 and 2 screws every 16 inches that is a total of 6 screws in the aluminum frame. This most likely will not get you near the capacity of the E-track. I recommend bolting through the aluminum frame so that…

view full answer...

Answer 2

I have the perfect solution for you. It's the Karrier ST225/75R15 Radial Trailer Tire with 15" Aluminum Wheel, part #AM32669. The wheel on this setup is a 15x6 wheel with an aluminum star spoke pattern. It has the 6 on 5-1/2" bolt…

view full answer...

Answer 3

We have a couple different options available for a spare tire mount inside your cargo trailer. - Rack'Em Spare Tire Rack for Enclosed Trailers #RA-16, this includes (1) spare tire holder but has the ability to hold additional tires with the…

view full answer...

Answer 4

Zinc plated screws are going to be the best option for use with aluminum to resist galvanic corrosion. This corrosion you are referring to is from two dissimilar metals reacting so you want to use the most similar metals when installing your E-track…

view full answer...

Answer 5

Hey Ken, thanks for reaching out! The Aluminum AM03 Series Matte Black Machined Trailer Wheel #AM93NR has a 3.74" pilot diameter which is a bit smaller than what you currently have. Does your 4.25" current pilot just barely fit on the hub,…

view full answer...

Answer 6

Lithium batteries require a higher charging voltage than standard batteries which a 12 volt trailer accessory source would not be able to provide. So while a lithium battery would do a great job it wouldn't be able to be charged when towing so a…

view full answer...

Answer 7

The best way to power the interior lights in your trailer is with its own independent battery. You will not want to use the breakaway battery. The breakaway battery is only designed to operate the breakaway and will drain extremely quickly,…

view full answer...

Answer 8

Hey Frank! Here's the standard for 7-way plug wiring: Green - Right Turn Yellow - Left Turn White - Ground Brown - Tail & Marker Lights Blue - Brakes Red/Black - Battery Purple - Backup I've also posted a photo of the standard wiring…

view full answer...

Answer 9

You are correct. There are just two differences between part #PS1400950376 and part #PS1400960376. The crank handle is included with part #PS1400950376, and it is painted black. The #PS1400960376 does not include the crank handle, part #PS1400920383,…

view full answer...

Answer 10

The Tekonsha Push-To-Test Trailer Breakaway Kit with Built-In Battery Charger - Top Load #50-85-313 is a much better option for your Breakaway system than having the trailer house battery serve that purpose. The way you wired the 12V input to your…

view full answer...

Answer 11

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Replacement Junction Box for Southland Trailer

Product Page this Question was Asked From

Continue Researching