Replacement Attachment Tabs for Demco Tabless Base Plates

Question

Question:

I need to find just the twistlock part for the Demco DM9519291 baseplate the towbar has gone missing with the twistlock parts dont want to have to replace everything can you help thanks

asked by: Reval S

1

Helpful Expert Reply:

It sounds like you are looking for the Replacement Attachment Tabs for Demco Tabless Base Plates # DM86MV. This includes both tabs and are the correct replacement tabs for the Demco Tabless Base Plate Kit # DM9519291.

expert reply by: Scott S

1

Answer 1

Hello Brad, thanks for reaching out. Yes the Roadmaster NightHawk tow bar is only directly compatible with Roadmaster Direct-Connect Base Plates. You can adapt it to a Demco tabless base plate using the following: - Roadmaster Sterling or Nighthawk…

view full answer...

Answer 2

You should consider updating to the Attachment Tabs #DM86MV for your Demco Tabless Base Plate Kit #DM34FR. Demco has changed over to these kinds of tabs in their kits. Otherwise you will need to reach out to Demco directly so they can verify the…

view full answer...

Answer 3

Thank you for passing on that the Demco tabs part #DM86MV from the etrailer base plate kits like the part #e98955 are a fit for the Roadmaster D-Ring adapter part #RM-031-5. The reason we didn't have them listed as a fit was basically just a…

view full answer...

Answer 4

What you are looking for is the Replacement Attachment Tab for Demco Tabless or etrailer Invisible Base Plates - Qty 1, #DM86MV. This will replace a missing tab, the removeable arm, of your etrailer Invisible Base Plate Kit, #e98948. Please note the…

view full answer...

Answer 5

Yes, there are adapters that will allow a Blue Ox tow bar to connect to a Demco base plate kit. For that you'd need the part #DM9523034 for if the base plate was a classic or a part #DM9523127 for if it's a tabless like the part #DM9519291…

view full answer...

Answer 6

Since you mentioned that you have either the: -Demco Tabless Base Plate Kit #DM9519336 for a factory plastic bumper Or -The Demco Tabless Base Plate Kit #DM9519339 for a factory steel bumper For your 2018 Jeep Wrangler JL Unlimited, the Replacement…

view full answer...

Answer 7

Good question, Chuck! You will not need the Brake Relay #RM-88400 when installing the Roadmaster 4 Diode Wiring Harness #RM-15267 on your 2018 Jeep Wrangler JL Unlimited. This is because the stop light switch circuit on your Jeep JL will go dead…

view full answer...

Answer 8

Hey Will! You can flat tow your 2014 Jeep Wrangler Willys with a Dana 44 axle as long as you have a two-speed transfer case. Make sure to check your owner's manual to verify this information. Does it have the standard bumper on the front?…

view full answer...

Answer 9

Hey Dan! Demco doesn't make specific adapters but you can use the Roadmaster Adapter #RM-035 (3/4" thick D-ring bumper mounts) or #RM-035-1 (1" thick) to attach it to your bumper. You will likely need some additional bushings for proper…

view full answer...

Answer 10

Yes the Roadmaster diode tow bar wiring kit part #RM-154 is a fit for your 2018 Jeep Wrangler JK Freedom Edition. Roadmaster does not recommend the use of the brake light relay part #RM-88400 with this either on your vehicle.

view full answer...

Answer 11

What braking system are you planning on using? If the system presses the brake pedal of the 2018 Jeep JK Wrangler like most do then yes you do need to use the #RM-88400. The reason for this is so that the stoplights of your Wrangler don't…

view full answer...

Answer 12

It sounds like you've created your own umbilical to go from the 7-way on your RV to a 7-way on your Jeep. The Hopkins connector #H20043 is 4 feet long, which isn't going to be long enough to bridge the gap of space for flat towing. You're…

view full answer...

Replacement Attachment Tabs for Demco Tabless Base Plates

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching