What Was Fixed With Current Version of Lippert Correct Track

Question

Question:

Why did Lippert discontinue the Correct Track? What were the issues? Does the newer Correct Track Third Generation address any issues from the original Correct Track?

asked by: John W

0

Expert Reply:

The previous generations of the Correct Track had some issues with brackets bending but the current generations like the single axle part # LC87120 and tandem axle # RR23QX have had all of that addressed and fixed.

expert reply by: Jameson C

0

Answer 1

We have lift kits for trailer that easily add 2 inches to the height of the trailer. For that you'd want the part #RR23QX and you'd be set. I attached a picture that shows how it installs to give you an idea. This would be the easiest…

view full answer...

Answer 2

Hello Jacques, thanks for reaching out. Yes, you can put just one MORryde X-Factor Crossmember #MR33WR on the center hanger for starter. MORryde does recommend doing all 3 for optimal support, but it is perfectly acceptable to start with just one as…

view full answer...

Answer 3

If you are going to install two of the MORryde X-Factor Crossmembers #MR33WR on your tandem axle trailer Alan you would want to install them on the front and rear hangers. You can install a third one if you want on the middle hanger as well for even…

view full answer...

Answer 4

The lift kit part #RR23QX is very similar to the Correct Track you mentioned. Basically they both share the same lift kit components but the Correct Track (no longer available) also had some alignment components that are no longer available at this…

view full answer...

Answer 5

I do still have a few options for lifting the trailer but the Correct Track Trailer Alignment and Lift Kit part #RR23QX is indeed incompatible with the MORryde CRE3000 Equalizers. Therefore, you can either change these out to standard ones like the…

view full answer...

Answer 6

Hey Mark, To plug the unused ports on your JR Products RV LP Gas Manifold #JR65CR you'll just need the JR Products RV LP Gas Manifold Plug #JR25CR. We also offer a couple of adapters to make your connection to the ports easier: 1/2" x…

view full answer...

Answer 7

Hey Zoniezz, thanks for reaching out! That flat pieces with the 3 holes from the MORryde X-Factor Crossmember Adapter Kit #MR93WR are spacers, and they can be placed between the mounting brackets and the crossmember (see blue highlight in linked…

view full answer...

Answer 8

Hey Jayden, thanks for reaching out! The Firestone W217602709 (part #F2709) is the correct air bag kit for your 2025 GMC Sierra 3500, and I’d definitely recommend sticking with the 7,500-lb bags for your setup. Trucks that carry consistent bed loads,…

view full answer...

Answer 9

Since your axles are already below your leaf springs the only option is the Correct Track Trailer Alignment and Lift Kit item #RR23QX. This kit mounts to your spring hangers and moves the attachment point down 1-1/4" or 2-1/4". This method…

view full answer...

Answer 10

Hi Nick; the MORryde X-Factor Crossmember for Standard Frame Hangers #MR33WR includes the following parts: 2- 7/16-20 Flange Locknut GRB Zinc 2- 9/16-7/16-20 x 3.4 Wet Bolt GR5 Zinc 20- 3/8-16 Flange Locknut GR8 Zinc 20- 3/8-16 x 1 Flange Bolt GR8…

view full answer...

Answer 11

Hey Jerry, GM moved the placement of their puck systems starting with 2020 models so you are correct that the pucks would have the hitch not sit directly over the axle. GM did the math and made sure that this placement wouldn't adversely affect…

view full answer...

Answer 12

Hey Zach. So long as your 2021 GMC Sierra 3500 has the factory puck system in the bed, the 25,000 lbs B&W Companion OEM 5th Wheel Hitch item #BWRVK3715 will indeed fit. This hitch is designed to drop right down into the four built in pucks that…

view full answer...

What Was Fixed With Current Version of Lippert Correct Track

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching