Trailer Wiring Harness for 2005 Ford E450 Shuttle Bus

Question

Question:

I want to hook up wiring for a trailer on my 2005 Ford E450 Shuttle Bus. What do I need, and where do I plug into the existing wiring?

asked by: James B

0

Expert Reply:

You'd need to go with a universal trailer wiring harness like part # 119250KIT for your 2005 Ford E-450 Shuttle Bus. This will give you a 4-way. If you instead need a 7-way you'd need to use the part # 37185.

expert reply by: Jameson C

0

Answer 1

I do have an option for you though there aren't custom fit hitches for box trucks. The frame is not really the issue but rather the body the up-fitter adds on which could hang down below the frame where the hitch mounts or actually use the holes…

view full answer...

Answer 2

Since you don't have a tow harness easily available you'll need to first install a 4-pole connector like #18002. The brown wire will tie into your E-450's running light circuit, yellow will tie into the left turn, green will tie into the…

view full answer...

Answer 3

The best brake controller for your 2019 Ford E-450 Cutaway is the Redarc Tow-Pro Elite Trailer Brake Controller item #RED44FR. The Tow-Pro Elite is very similar in design to a factory trailer brake controller. There is a control box that gets…

view full answer...

Answer 4

I have a solution for you that I can provide, but we aren't going to have a custom fit hitch to fit a vehicle like what you referenced. I spoke to my contacts at Curt and Reese and the only styles of hitches that can be made to fit a service body…

view full answer...

Answer 5

Looking to the towing section of the owners manual for the 1999 Ford e450, though it never specifically calls out the e450 model in the Trailer Towing Table, for every model with a 7.3 Diesel and 4.10 rear axle ratio, the maximum GCWR is around…

view full answer...

Answer 6

If you're speaking of the video showing the #119178 being installed on a 1999 Ford Van (see link), the harness is wired into the vehicle side of the van, closer to the front of the vehicle. The vehicle being wired in the video had a…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 11

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 12

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Trailer Wiring Harness for 2005 Ford E450 Shuttle Bus

Continue Researching