Mounting TorkLift GlowStep Camper Scissor Steps to 2022 Adventurer 80RB

Question

Question:

Any idea how people are mounting this on an Adventurer 80RB on a Ford F350? There is only an inch below the camper door. It also doesnt seem like any spot on the truck. Adventurer recommends these steps though, so any help would be great.

asked by: Mike G

1

Helpful Expert Reply:

The TorkLift GlowStep Camper Scissor Steps, # TLA7805-8000 has a mounting bracket that attaches to the camper and held in place with included lag screws.

expert reply by: Michael R

1

Answer 1

Not following the manufacturer's instructions to the letter will give them an excuse if something were to happen so while I can't recommend drilling the extra holes to ensure it's safely mounted, it's the only way that the steps will…

view full answer...

Answer 2

Hi Mark, If you have a Furrion Chill Cube 18K air conditioner like the part #FR27TD, that unit comes with a built-in soft start to keep current spikes low when the compressor kicks on, so you won't need to install one. If you have a Furrion Chill…

view full answer...

Answer 3

We can set you up with new steps so that you love your whole camper setup, steps included. Based on the information you provided, I recommend taking a look at the Brophy Camper Scissor Steps #AS25. This is a 5-step assembly that can expand to between…

view full answer...

Answer 4

For your mounting height of 43 inches the best solution we have is the part #AS25 which has a mounting bracket height of between 40" - 48" which would be perfect for you. The additional step you mentioned would not interfere with that…

view full answer...

Answer 5

That is a good question, and you can leave your current fold-out steps up and in the folded position when installing the mounting bracket of the Brophy Scissor Steps. The reason is, the bracket will be installed just underneath the door so as long as…

view full answer...

Answer 6

Those loops you see on the side of the brackets on the #TLA8000 are for the TorkLift GlowGuide Handrail #TLA7621. I attached a picture that shows how the handle attaches to those loops.

view full answer...

Answer 7

Which holes are you talking about specifically on the steps?

view full answer...

Answer 8

Great question! The All Terrain Landing Gear for RV Scissor Steps, #TLA8000, work with most factory scissor steps. Many steps like Brophy Scissor Steps #AS23 use rivets. You are correct - the rivets will need to be drilled out using a 1/4" drill…

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Mounting TorkLift GlowStep Camper Scissor Steps to 2022 Adventurer 80RB

Product Page this Question was Asked From

Continue Researching