Replacement Circuit Board for Atwood GC66A10E Water Heater

Question

Question:

Do you have a circuit board for a Atwood hot water heater model GC66A10E OR # PART 91346B. ?

asked by: Nick L

0

Expert Reply:

We do! The correct part for your Atwood model GC66A10E is the Replacement Circuit Board for Dometic Atwood Water Heaters # DMC89FR. I confirmed this with my contact at Dometic.

expert reply by: Jon G

0

Answer 1

Thank you for the photos! From what I'm seeing it looks like you need the Replacement Lift Arm #FVK8011-05 and the Replacement Dome #FVK1020-19 for your main vent. The dome should be an exact replacement while the lift arm doesn't have the…

view full answer...

Answer 2

The Classic Accessories PolyPro III Deluxe Travel Trailer Cover part #052963732634 is a great fit for your trailer. It's designed for trailers that are between 20 and 22 feet like yours and has zippered access panels that will line up with the…

view full answer...

Answer 3

There are indeed many different replacement step controllers out there and I am happy to re-confirm that the correct current item to replace your Kwikee step controller 1800709 is part #LC363989. I verified this item with my parts contacts at…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 9

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Replacement Circuit Board for Atwood GC66A10E Water Heater

Product Page this Question was Asked From

Continue Researching