Replacement Mount Assembly For Subaru SOA567B011 & Thule Circuit XT Bike Rack

Question

Question:

Will this fit Subaru Oem SOA567B011?

asked by: Ruel

0

Expert Reply:

You will need the Replacement Rear Mount Assembly # TH55RH for your Subaru Thule Circuit XT bike rack. This is the correct replacement part according to Thule for the Subaru SOA567B011 bike rack.

The Replacement Around the Bar Bracket # 1500052940 is specific to the ProRide XT and UpRide bike racks.

expert reply by: Bud M

0

Answer 1

The Thule Big Mouth was able to mount to Thule Aero Bars with the xadapt2. That was a t-channel mounting system. I spoke with a Thule rep and she said there was never a mount for aero/factory rack bars that did not have a t-channel. I remember when…

view full answer...

Answer 2

I spoke with my contact at Thule and when I described your situation she said that it sounds like you have the older style Sidearm and need a few parts so that you could convert it to the newer style. My contact provided me with the replacement parts…

view full answer...

Answer 3

What you need is the Thule XADAPT2 AeroBlade and Xsporter Load Bar Adapter for Roof-Mounted Carriers #Xadapt2. This adapter will allow you to mount your Thule 599xtr Big Mouth bike rack on your 2022 Subaru Legacy Aero crossbars.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

Hey Melanie. The reason you can't find a replacement for your GE ARC15AACBL2 15,000 btu air conditioner is because they phased them out. In 2025 all RV AC systems had to change over to a new coolant called R32. This was a EPA mandated decision.…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Replacement Mount Assembly For Subaru SOA567B011 & Thule Circuit XT Bike Rack

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching