Does the Rim or the Valve Stem Determine the Maximum Pressure

Question

Question:

I have some trans eagle 16ply tires that hold 115 psi and I have 16” rims with all metal valve stems on my dump trailer. Is there any 16” rims that aren’t capable of holding that much air or is it the valve Stem that really matters in this situation?

asked by: Chris M

0

Expert Reply:

Rims like the Aluminum Split Spoke Trailer Wheel - 16" x 6-1/2" Rim - 8 on 6-1/2 # AM22659HWT do not have a psi rating. Like you said, it is the valve stem that will be the limiting factor for tire pressure. For example, the Americana Metal, Bolt-In Valve Stem # AM20906 is rated for up to 200 psi where the Americana Rubber, Snap-In Valve Stem # AM20903 can only hold up to 65 psi.

expert reply by: Robin H

0

Answer 1

Hi Rob! We definitely have 13" wheels with the 4 on 4 bolt pattern and 185/80R13 tires, but we do not have any already mounted, unfortunately. The 4 on 4 bolt pattern isn't super popular with the 13" wheels for some reason, so you will…

view full answer...

Answer 2

The tires in your size that we offer have varying pressure ratings depending on their load capacity. For example, if you look at the tires in your size shown on the link I have included you will see that those rated for Load range E, such as…

view full answer...

Answer 3

I spoke with one of the engineers at HWT and he told me that the psi rating for an HWT wheel and tire assembly is only limited by the valve stem and tire. If your current wheels or new wheels have a psi rating under 110 psi, it is okay to use tires…

view full answer...

Answer 4

We do have a solution for you but you are going to need to know your wheel's bolt pattern in order to get the correct wheel. Since you mentioned you had a 20.5x8.0-10 tire (which is the same size as a 205/65-10 trailer tire) we know you have a…

view full answer...

Answer 5

Generally, I do recommend that all tires on your trailer be the same size at all times, so ideally your spare will match the existing tires on your trailer. With that being said, the difference between a 175/80-13 and a 175/80-13 tire is only 0.3 of…

view full answer...

Answer 6

The same dynamics for passenger tires are not applicable for trailer's. Therefore, I do not recommend using a smaller tire on your trailer as a spare. The spare tire on a vehicle is mainly designed to get you to the nearest repair station. The…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 9

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Does the Rim or the Valve Stem Determine the Maximum Pressure

Products Featured in This Question

Featured Help Information

Miscellaneous Media

Continue Researching