Stabilizer Pad For 12 Inch Octagon RV Jack Plate

Question

Question:

Do you guys carry Jack pads like the SnapPad or similar that fit 12” Hexagon Jack Feet Thanks...

asked by: Don

0

Expert Reply:

I have a solution for you.

After talking with my contact at RV Snap Pad and researching this foot pad you have. They do not make a snap on pad that fits this type of application.

The lips on your foot are to tall and they do not have anything that can fit on them.

You will need to go with a stabilizer pad like the Stromberg Carlson RV Jack Pads for RVs and Trailers - 14" Long x 12" Wide - Rubber - Qty 2 # SC57VR.

expert reply by: David B

0

Answer 1

Hi Uwe! Yes, the SnapPad StakPad Universal Leveling Block and Jack Pad #SN24VR can hold that weight. These have a capacity of 40,000 lbs, so as absurd as it may seem a single jack pad can handle the entire weight of your Class A. Using these under…

view full answer...

Answer 2

Hi Glen, It will depend on what the GVWR (gross vehicle weight rating) is of your trailer to determine which B&W 5th wheel to gooseneck adapter will work best for you. Fifth wheels and gooseneck trailers go off of pin weight instead of tongue…

view full answer...

Answer 3

Hey Max. There's no database that shows me what pin box is on your Montana 305RL and Keystone doesn't list that information either. I'll need the information on the sticker that's attached to the brackets above your current pin box to…

view full answer...

Answer 4

Tyler, great question - and it’s definitely more than cosmetic. The etrailer electric trailer jacks #e72QV and #e22QV are mechanically identical 3,500 lb jacks. Same motor, same lift height of 18", same 7-way plug power. The only difference is…

view full answer...

Answer 5

Hey Michael! Since you were looking at the SoftStartRV Soft Start #SSR54FR are you wanting that built in as well? The Active Controls ActiveStart Plug-In Soft Start for RVs #AS94FR is a soft start and surge protector all in one. If you aren't…

view full answer...

Answer 6

Sure thing! To complete your flat tow setup for your 2018 Ford Expedition, you will also need: 1. A base plate kit, like the Roadmaster Direct-Connect Base Plate Kit #RM-524457-5. You'll need a base plate kit to connect your tow bars to your toad…

view full answer...

Answer 7

The Buyers Products Polymer Outrigger Pad 24" x 24" x 1-1/2 " #337OP242415 weighs just under 30 lbs. This high density polyethylene product has a shipping weight of 30 pounds, so the product will be just under that amount out of the…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 10

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 11

Good question, Dave. The easiest way is to match the RVpaws kit to your jack leg or leveling system. For example, there are specific kits for the brands and lineups out there: Standard 2" round jack leg = #RV57FR Standard 2" square jack leg…

view full answer...

Answer 12

Hey Ken, yes the Replacement Pad for SnapPad Jack Stand Pad System #SP74FR that you referenced is made by Snappad. This is for sure not a knock off! What camper do you have?

view full answer...

Stabilizer Pad For 12 Inch Octagon RV Jack Plate

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching