Replacement Wheel Hub Cover For A 2007 Jayco Seneca With 19.5 Alcoa Wheels

Question

Question:

I have a 2007 Jayco Seneca with 19.5 Alcoa wheels. I lost a rear hub cap. I see you have the replacement with #PXQ822R or PXQ820R. How do I know what size lug nut and stud I have? Thanks for your help.

asked by: Mark

0

Expert Reply:

The stud doesn't matter when it comes to the wheel cap, you just need to measure the width of the lug nut to ensure the Phoenix USA Rear Hub Cover w/ Pop Out # PXQ822R or Phoenix USA Rear Hub Cover w/ Pop Out # PXQ820R will fit the lug nut.

The # PXQ822R is going to fit 33mm lug nuts and the # PXQ820R is going to fit 30mm lug nuts.

expert reply by: Kevin C

0

Answer 1

Hi Jose, Phoenix USA doesn't list the lug nuts of the Phoenix USA Rear Hub Cover w/ Pop Out #PXQ820R as a replacement item but I'm sure if you gave them a call they be happy to send you some replacements.

view full answer...

Answer 2

I reached out to my contact at Phoenix USA and the Phoenix USA Front Hub Cover w/ Pop Out - 8 on 275mm - 33mm Lug Nuts - ABS Plastic #PXQ822F you were looking at will work with your 2014 Thor Challenger with 8 lug 22.5" wheels as long as your…

view full answer...

Answer 3

Hello John. We do offer center caps for the 8 lug wheels. Take a look at the Phoenix USA Rear Wheel Center Cap #PXPH1843. This will fit wheels with a 8 on 275mm bolt pattern and will fit hubs with a diameter of 6-1/2" or 8-1/4". So, as long…

view full answer...

Answer 4

It depends on what size lug nuts you have. There are two options and I have listed them both below: 13/16" Lug Nuts - Phoenix USA QuickTrim Hub Covers item #PXQT765CHN 7/8" Lug Nuts - Phoenix USA QuickTrim Hub Covers item #PXQT865CHN Both…

view full answer...

Answer 5

Yes Dustin, the etrailer Electric Trailer Brakes #AKEBRK-7-SA you're looking at will work fine as a replacement. As far as the bearings, seals, and everything else goes, you can use the Dexter Trailer Hub & Drum for 5,200- to 7,000-lb Axles…

view full answer...

Answer 6

The Red and Amber Self-Adhesive Reflector Kit #RE52ARK are 4 inches long, 1-1/4 inches tall, and 3/8 of an inch thick. I have linked a video that shows this for you.

view full answer...

Answer 7

The trailer brakes work on a separate circuit than the lights. You have a couple of options to control the electric brakes on the trailer. One option is to use an air over electric brake control, #HA100400C. This unit connects to the air brakes on…

view full answer...

Answer 8

Yes, it will! I checked with Phoenix USA and their Front Hub Cover w/ Pop Out item #PXQ822F, you were looking at, will work with your 2008 Fleetwood Southwind with 8 lug 22.5" wheels since your factory lug nuts are 33mm.

view full answer...

Answer 9

Since you said your hub says 8-219 that would indicate that you need the Dexter hub part #8-219-13UC3 as a replacement. This is a hub for higher capacity axles between 5,200 and 7,000 lbs and has a bolt pattern of 8 on 6-1/2 inches.

view full answer...

Answer 10

I reached out to Phoenix USA and was able to determine that the center cap of the Phoenix USA Rear Hub Cover #PXQ820R is part #PHX59FR.

view full answer...

Answer 11

Based on your photo, it looks like you have something like the Phoenix USA Rear Hub Cover w/ Pop Out - 8 on 275mm - 33mm Lug Nuts - ABS Plastic #PXQ822R which includes screw-on lug nut covers. There are not any replacement screw-on lug nut covers for…

view full answer...

Answer 12

Hey Cindy! The only replacement camera we have for your Voyager VBCS150 is the Voyager Rear Camera with LED Low Light Assist item #VCMS17B. It uses the same connector as your VBCS150, however the mounting bracket is different so you'd need to use…

view full answer...

Replacement Wheel Hub Cover For A 2007 Jayco Seneca With 19.5 Alcoa Wheels

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching