Replacement Center Cap For Phoenix USA Rear Hub Cover # PXQ820R

Question

Question:

Can you please provide a part number for the center pop out cover on the PXQ820R?

asked by: Tony J

0

Expert Reply:

I reached out to Phoenix USA and was able to determine that the center cap of the Phoenix USA Rear Hub Cover # PXQ820R is part # PHX59FR.

expert reply by: Kevin C

0

Answer 1

Hey Cindy! The only replacement camera we have for your Voyager VBCS150 is the Voyager Rear Camera with LED Low Light Assist item #VCMS17B. It uses the same connector as your VBCS150, however the mounting bracket is different so you'd need to use…

view full answer...

Answer 2

The stud doesn't matter when it comes to the wheel cap, you just need to measure the width of the lug nut to ensure the Phoenix USA Rear Hub Cover w/ Pop Out #PXQ822R or Phoenix USA Rear Hub Cover w/ Pop Out #PXQ820R will fit the lug nut. The…

view full answer...

Answer 3

Based on your photo, it looks like you have something like the Phoenix USA Rear Hub Cover w/ Pop Out - 8 on 275mm - 33mm Lug Nuts - ABS Plastic #PXQ822R which includes screw-on lug nut covers. There are not any replacement screw-on lug nut covers for…

view full answer...

Answer 4

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 5

Hello Bruce, Thanks for writing in! Using butyl tape between the trailer body and the Single Axle Jeep Style Trailer Fender - Diamond Plate Aluminum - 13" to 15" #HP96VR is exactly the route I would go. It stays flexible, creates an…

view full answer...

Answer 6

Hi Jose, Phoenix USA doesn't list the lug nuts of the Phoenix USA Rear Hub Cover w/ Pop Out #PXQ820R as a replacement item but I'm sure if you gave them a call they be happy to send you some replacements.

view full answer...

Answer 7

Hey Tom, With those Magnetek 6700 Series no longer being around I recommend the Progressive Dynamics #PD4045KA. This is an upgrade since we no longer carry any 30-35amp units, this will upgrade you to 45 amps of output. You will need to modify the…

view full answer...

Answer 8

We have the perfect solution for you. I'd recommend using the Fulton weld-on drop leg stabilizer jack, part #FSJ1-SJ2. The jack is sold individually, but using two of them would provide 6000 lbs of support which would be plenty, as your trailer…

view full answer...

Answer 9

I have an option for you, but custom fit floor mats from WeatherTech are not available for any Class A motorhome. Take a look at the WeatherTech All-Vehicle Mat #61-11AVMOTHSG, instead . These universal floor mats can be trimmed with a pair of sharp…

view full answer...

Answer 10

The OL or Overload error code is displayed when the brake circuit is drawing too much current, possibly caused by a short on the brake wire or a poor ground connection at the brake magnets. Your situation is a bit confusing so the best recommendation…

view full answer...

Answer 11

The EB01-140 and EB01-145 are Redneck Trailer Supply part numbers for a Dexter 12-1/4 x 3-3/8 7-bolt brake assemblies for a 9-10K axle. The proper replacements are available as part #23-450-451, which includes the left and right self adjusting brake…

view full answer...

Replacement Center Cap For Phoenix USA Rear Hub Cover # PXQ820R

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching