Replacement Hardware for Yakima Kingpin 4

Question

Question:

Hi, Im looking for the bolt kit I have a Kingpin 4 and it was unclear which bolt I needed from the website.

asked by: John A

0

Expert Reply:

For replacement hardware for your Yakima Kingpin 4 you need the Replacement Shank and Pivot Hardware # Y8780018. This comes with the hitch bolt and clip, along with the hex bolts, washers, bolt sleeves and lock nuts required to mount the pivot shank.

expert reply by: Robin H

0

Answer 1

We have actually seen this issue before. The 2" receivers on Toyota trucks and SUVs have a slightly larger diameter on the outside of the receiver tube than most typical 2 inch hitches. This is partially the powder coating, but the steel itself…

view full answer...

Answer 2

Hi Julio; there are three different U-bolt sizes for the Thule Canyon XT Roof Cargo Basket #TH859XT. You can choose from the following: -Replacement U-Bolt for Thule Trail Large and Medium Cargo Baskets - 40 mm x 90 mm #1500052553 -Replacement U-Bolt…

view full answer...

Answer 3

I went out to the warehouse and pulled replacement u-bolt #853-3105 to take some measurements. The width between the two ends is approximately 2-7/16 inches. The center to center distance though is 2-11/16 inches. The internal length is 3-1/2 inches…

view full answer...

Answer 4

The SportRack Replacement Hardware Kit for Explorer and SkyLine XL Roof Mounted Cargo Boxes #SR05587 has basic components for mounting. Just the crossbar mounting hardware for this kit is found in the Replacement Hardware Kit for Searsbox Cargo Box…

view full answer...

Answer 5

We have previously confirmed with Thule (the manufacturer of this cargo box) that the correct replacement mounting hardware for your Sears X-Cargo 28-7271 is the Replacement Hardware Kit #SR05587 which does include the U-bolts required for this cargo…

view full answer...

Answer 6

No, the Thule Snug Tite lock #THSTL2 is not a confirmed fit for the Yakima Kingpin bike rack but you can use the Yakima lock #Y07235. This lock fits the threaded pin that came with the Kingpin bike rack. I have linked a video review of this lock for…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Replacement Hardware for Yakima Kingpin 4

Continue Researching