Correct Idler Hub Replacement for Dexter 84546 Hub

Question

Question:

Hello, I have a 3500lb hub stamped 84546. It is 5 x 4.5. Will Item # AKIHUB-545-35-K fit or can you tell me what would be the proper fit? Thanks,

asked by: Paul E

1

Helpful Expert Reply:

Yes, the Trailer Idler Hub Assembly part # AKIHUB-545-35-K will work in place of a Dexter 84546 Hub.

expert reply by: Conner L

1

Answer 1

We offer both traditional petroleum-based wheel bearing grease and also more environmentally-friendly bio-based grease products that are produced from crops. It is permissible to mix the two types. From your description it appears you may have…

view full answer...

Answer 2

The standard 3,500 lb axle uses the Hub Bearing Kit #BK2-100 which is for a #84 spindle. If your axle is a 1990 or newer then you likely need these parts but if it's older then I'll need you to measure your spindle to make sure we can get you…

view full answer...

Answer 3

Normally, with a serial number on your Dexter Axle, we are able to determine a proper replacement for your axle. However, after having spoken with Dexter, the only information they were able to provide was that it was made in 1998 and has a capacity…

view full answer...

Answer 4

You can confirm the weight rating of your Dexter axle by removing one hub and pulling its bearings. The included photo shows how part numbers usually appear on bearings. The specific bearings used will tell you the axle's weight rating. Just…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Correct Idler Hub Replacement for Dexter 84546 Hub

Product Page this Question was Asked From

Continue Researching