Availability of Just Shank of Curt Adjustable Ball Mount part # C45926

Question

Question:

Can I buy just the hitch shank for the Curt 45926 ? I already have the Curt double ball. Thanks,

asked by: James L

0

Expert Reply:

Curt does offer just the replacement shank for the Adjustable Ball Mount part # C45926 with the part # C45910.

expert reply by: Jameson C

0

Answer 1

Hey David, thanks for reaching out! The shank on the Curt Adjustable 2-Ball Channel Mount #C45926 isn't available by itself, unfortunately. What were you planning on using it for? I might be able to find an alternative solution for you!

view full answer...

Answer 2

The shank of the C45926 is not available separately. If you needed the greater rise/drop that this provides you'd need to go with an all new #C45926.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 7

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 8

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Hey Rob, thanks for reaching out. Yes, we do have dash-mounted brake controller options for your 2004 GMC Sierra 2500HD. If you want a standard controller that mounts on the dash, I recommend the following: - Curt TriFlex NEXT Trailer Brake…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

Hey Kelly! The Curt 13146 fits 2016 - 2022 Honda Pilot. What you need for your 2026 Honda Pilot is the Curt #C22HR. This has a bolt-on installation and does not require any cutting or trimming of the bumper so you won't be modifying the vehicle.…

view full answer...

Availability of Just Shank of Curt Adjustable Ball Mount part # C45926

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching