Correct Replacement Grease Seal for 6K/7K Trailer Axle

Question

Question:

I have a pipe trailer Im not sure if its 6K axles or 7 k will arent it the only numbers I can find are on the wheel seal than the outer bearing 25580 010-036-00

asked by: Shawn

0

Expert Reply:

If you're looking for grease seals then it will be either part # GS-2250DL which measures 2.250" at the I.D. or part # GS-2125DL which measures 2.125" at the I.D. We also have bearings kits with the latter seal, part # BK3-110. You'll need to measure to determine which seal you need. If this was not what you were looking for please let me know what that is instead.

expert reply by: Conner L

0

Answer 1

I can help you figure out which grease seal you will need for your toy hauler. I am aware of two types of axles out there that use both those identical bearing sizes but different seals so you will need to measure your spindle to be for sure if the…

view full answer...

Answer 2

Hi Dale, that seal has a 2.312" inner diameter and 3.376" outer diameter which isn't something we carry. Are you sure that is the correct grease seal for your trailer? Unless it is a really old trailer, or home built with mobile home…

view full answer...

Answer 3

Hey Brian, the Grease Seals 10-36 #RG06-070 are most commonly found on 8k trailer axles so you could potentially use these, but I'd recommend measuring the inner and outer diameter of your current seals to make sure they fit. If you measure 2 1/4…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 10

Hi Calvin! All of the pre-greased hubs/drums, like the Terran Industries Trailer Hub and Drum Assembly - 3.5K Axles - 10" Diameter - 5 on 4-1/2 #TX68VJ, come with bearings made overseas and are all basically the same quality. At least that I…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

I currently have four different self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes. You can choose from the following: -Terran Axle Electric Trailer Brakes #TX97ZJ (3,500 Axles) -etrailer Electric Trailer…

view full answer...

Correct Replacement Grease Seal for 6K/7K Trailer Axle

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching