Is Bolt Pattern between B and W Hitches BWHDRH25122 and BWHDRH25198 the Same

Question

Question:

I have a 97 f250 with regular bumper on it now. The previous owner had s flatbed on it and theres existing holes drilled for hitch. I was wondering if these two hitches have the same bolt hole measurements. I know one is for a deep bumper. BWHDRH25122 and BWHDRH25198

asked by: Dustin B

0

Expert Reply:

Since the only difference between the B and W Hitches # BWHDRH25122 and # BWHDRH25198 is the style of bumper they fit with the bolt pattern is the exact same. Only difference is the height difference relative to the hitch opening and where it mounts to truck frame.

expert reply by: Jameson C

0

Answer 1

Hey Tim! The distance from the most rear hole to the end of the #BWHDRH25122 receiver tube is going to be 12". See the attached photo.

view full answer...

Answer 2

Hello Doug, thanks for reaching out. In regards to the B&W Heavy-Duty Trailer Hitch Receiver #BWHDRH25198 the distance from the mounting surface to the top of the receiver tube is 7.9". Take a look at the picture I included. The #BWHDRH25198…

view full answer...

Answer 3

I would be happy to and thanks for the pictures! The B&W Heavy-Duty Trailer Hitch item #BWHDRH25122 measures 5.4" from the top of the frame brackets to the top of the receiver and 19-1/2" to the back of the receiver from the last bolt.…

view full answer...

Answer 4

If your 1989 Ford F-250 4WD with heavy-duty towing package has a deep-drop type bumper then the only option in a 2-inch Class V hitch is the B&W #BWHDRH25198 which DOES require you to adjust the positioning of the spare tire mount. The other…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Is Bolt Pattern between B and W Hitches BWHDRH25122 and BWHDRH25198 the Same

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching