Can Axle Perches Be Welded to the Frame?

Question

Question:

The manufacturer of my trailer Carson Trailers just welded the axle perch straight to the trailer frame. Can these be welded to the frame or should I buy the brackets shown in other pics not sure the name of them and have them in stalled prior to installed these?

asked by: Donn J

0

Expert Reply:

Thanks for the picture! That axle perch is usually attached to your trailer's frame with bolts not a weld. I would definitely consult with the dealer you purchased your Carson trailer from. I recommend attaching the Lippert Axle Riser Kit - Single Diamond Torsion Axle item # LC270682 with the included hardware and not welding it to your motorhome.

expert reply by: Jerred H

0

welded axle perch
(click to enlarge)

Answer 1

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 2

To mount the Channel Tongue Trailer Coupler - Trigger Latch - Bolt On #CT-5003-Z, I recommend using 1/2 inch bolts. The higher the grade, the stronger the bolt. I've attached the review video to help as you plan this installation.

view full answer...

Answer 3

Given that trailer wiring only consists of basic light functions, 12 volt power, and brake output a system of fuses is not necessary because it is easy to determine if something is not working. If there was a short, the way you would know with or…

view full answer...

Answer 4

The spring seats are already welded on the Dexter Trailer Axle Beam with EZ-Lube Spindles - 89" Long - 3,500 lbs #T3584F-EZ-8974 you were looking at. They are welded 74" apart center to center, and the axle has an 89" hub face to hub…

view full answer...

Answer 5

An axle without idler hubs would not have a left or right side assigned to it. It could basically be ran either direction. If it has brake assemblies installed though then it would need to face the right direction. Otherwise you'd have to swap…

view full answer...

Answer 6

We do have what you need to add a 7-way trailer connector to your 2018 Subaru Outback Wagon but there isn't a specific custom harness that fits. If right now the Outback has no trailer wiring at all the easiest way to add a 7-way is to start with…

view full answer...

Answer 7

The Trailer Axle w/ Electric Brakes - EZ-Lube - 5 on 4-1/2 Bolt Pattern - 89" - 3,500 lbs #e43SR can have the spring locations changed. You can simply have the Spring Seat for Typical 3,500-lb, Round Trailer Axles with 2-3/8" Diameter…

view full answer...

Answer 8

It is highly recommended that the spring seat be at minimum tack welded to the axle. There have been issues that have resulted from the seat not be welded to the axle. If you do not have access to a welder, I recommend taking the trailer to a local…

view full answer...

Answer 9

You can certainly relocate the spring perches if you wish, it's a pretty common practice. The process of removing them will likely render them useless, however so you'll likely need to replace them. We offer replacements as part #TRSS238…

view full answer...

Answer 10

Thanks for the picture Rich. The BTR E-Z Lube Spindle for 2,000-lb Trailer Axles - 1-1/4" Diameter item #TRU44FR is exactly what you need if your hubs have item #L44649 inner and outer bearings. For a grease seal you'll want item #34823. We…

view full answer...

Answer 11

A leaf spring seat, or perch as it sometimes called, is the mount that is welded to the axle where the trailer's leaf springs sit on top of or below the axle. An example of one is part #TRSS300. I've attached a picture that points out the…

view full answer...

Answer 12

Yes! You can weld the springs seats to a different location on Dexter trailer axle #20440I-ST-60. But instead of cutting off the ones on the axle and welding them back on I recommend getting new springs seats, #TRSS175 (sold in quantities of 1), and…

view full answer...

Can Axle Perches Be Welded to the Frame?

Continue Researching