Locating Tail Light Wires on a 2013 Infiniti JX35 to Install the Curt 3 Wire to 2 Wire Converter
Published 06/14/2013
Question:
hi, I bought the trailer wiring harness part # C56190 for my Infinity JX35. The instructions are not clear where the box to connect the wiring harness is located in the car. Can you provide a picture or a description where the box is and how to go to it? Thanks
asked by: Greg K
Expert Reply:
The Curt Universal 3 Wire to 2 Wire Harness, # C56190, that you purchased was designed to connect directly to your vehicles tail light circuits. This wiring harness was not designed to connect to a specific box or connector on any particular vehicle. You should be able to access the tail light circuits on your 2013 Infiniti JX35 either directly behind the tail light assemblies, or you may be able to find the behind the trim panels in the rear cargo area on the driver and passenger side of the vehicle.
Often times there is an access door on the trim panels where you may be able to locate the wires, but you may need to completely remove the rear trim panels. On SUVs like your JX35, we have had luck splicing into the tail light wiring directly behind the tail light assemblies. The tail light assemblies are usually held on with a few clips or screws. Once the clips or screws are released, the tail light assembly can be pulled out.
The converter box can be mounted in any location as long as it is away from the elements. I strongly recommend using a circuit tester like part # PTW2993 to test the taillight wires before you make any connections to ensure you have the correct wire.
One thing to keep in mind with this wiring harness. Be sure you connect the Black wire directly to the positive terminal on your vehicles battery. This 12 volt power wire will supply the power to your trailer lights and the wiring harness will not work properly if it is not connected to the battery.
I have attached an FAQ article on tips for routing the power wire for you to check out.
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Trailer Wiring
- Article: Routing the Power Wire for a Trailer Wiring Harness
- Q&A: Recommended Trailer Wiring Harness for 2013 Infiniti JX35
- Shop: Curt Powered Tail Light Converter w/ 4-Way Flat Trailer Connector and Install Kit
- Shop: Trailer Hitch
- Video: A Closer Look at the Hook Probe Circuit Tester
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Q&A: Modifications Required to Install Class III Trailer Hitch Receiver on 2014 Nissan NV200 Van
- Article: Trailer Wiring Diagrams
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Search Results: trailer hitch
- Video: Curt T-Connector Vehicle Wiring Harness Review C56040
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Search Results: trailer wiring
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Suspension Enhancement
- Video: Clean Up Your Trailer Wiring
- Article: How to Choose the Right Trailer Hitch Class
- Search Results: trailer tires and wheels
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Shop: Brake Controller
- Search Results: trailer jack
- Q&A: Installation Time for Blue Ox BX1128 Flat Tow Base Plate Kit for 2016 Jeep Grand Cherokee
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Article: How to Measure for Trailer Hitch Drop
- Video: How to Choose a Trailer Brake Controller
- Shop: etrailer Anti-Rattle Hitch Collar for 2" Hitch Receivers
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
on Custom Fit Vehicle Wiring
