Front Panel and Folding Panel Length of Bak Tonneau BAK48331 For 2022 Ford F-250 Long Bed

Question

Question:

For a Ford F-250 with an 8 foot bed, what is the measurement of the stationary flap, and what are the measurement of the rest of the foldable sections? Thanks for your help

asked by: Bill

0

Expert Reply:

The front header panel of the Bak tonneau cover part # BAK48331 that fits your 2022 Ford F-250 long bed is about 6 inches long and each of the folding sections is about 22-1/2 inches long.

expert reply by: Jameson C

0

Answer 1

The Extang Solid Fold 2.0 Hard Tonneau Cover - Toolbox Edition #EX84488 sits on top of the bed rails of your 2022 Ford F-350 Super Duty 8' bed so if your 5th wheel hitch sits below the top of your bed rails this will physically fit in that…

view full answer...

Answer 2

For a tonneau cover to use with a gooseneck trailer the BAKFlip MX4 won't be your best option as it's either going to fold up against the back glass and block total view or it's going to fold down on the last panel and be thick enough…

view full answer...

Answer 3

The BAK Revolver X4s Hard Tonneau Cover #BAK49ZR which fits your 2023 Ford F-350 8' long bed has to be in either the fully rolled up or fully covered position. If you go with a cover like the BAKFlip MX4 Hard Tonneau Cover #BAK48331 you will be…

view full answer...

Answer 4

It really depends on how much room your tool box takes up in the bed of your 2017 Ford F-350. If it sits near the front (cab-side) of your bed and is about as tall as the sides of your bed then you will need to move it forward because there is a…

view full answer...

Answer 5

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 6

Hey Kelvin, welcome back. To flat tow a 2026 Ford Maverick with your Demco Commander II Tow Bar item #DM9511012, I recommend the following parts: Baseplate Kit - Demco Tabless Base Plate Kit item #DM38CV Wiring Harness - Roadmaster Diode 7-Wire to…

view full answer...

Answer 7

Hey Richard, our most popular tonneau cover for your 2026 Ford F-450 long bed would be the Pace Edwards UltraGroove part #PE87QJ which is low profile like you want, would allow your fifth wheel hitch to fit easily, and also is retractable which makes…

view full answer...

Answer 8

Hey Ken! Based on the photos and measurements you provided, your current shackles look to be right around 3-1/8" from the center of one bolt hole to the center of the other, so you're definitely looking in the right direction. Since…

view full answer...

Answer 9

The problem that you would run into with a folding cover such as #BAK72331 is if you leave it on but folded up flat it will be several inches above the truck bed sides. This means that when making tight turns the trailer's pin box could make…

view full answer...

Answer 10

Hey Ken! The 6,000 lbs. 6760401 Dexter axle on your Keystone Cougar 316RLS is a 3" axle, so the perfect u-bolt kit for you is the U-Bolt Kit for Mounting 5,200-lb to 7,000-lb, Round Trailer Axles #APUBR-8. This u-bolt kit will work seamlessly…

view full answer...

Answer 11

Hey John, yes the Everchill #EV27FR would fit in a 25 inch deep cabinet like you mentioned. This would be a really solid option to replace your Norcold so I think you should go for it. This is also our best fitting option for replacing what you have…

view full answer...

Answer 12

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Front Panel and Folding Panel Length of Bak Tonneau BAK48331 For 2022 Ford F-250 Long Bed

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching