Replacement Hitch Lock For Thule Expressway 996XT Bike Rack

Question

Question:

I have a 15 year old Thule Expressway 996XT rack and need a replacement bolt and lock to attach to my hitch. I found the model on the thule website but the replacement parts are no longer available. Can you help me figure out a replacement part?

asked by: Sharon L

0

Expert Reply:

We do have the correct replacement hitch bolt and lock for your Thule Expressway 996XT bike rack; I verified with Thule the correct part is the following:

- Thule Snug Tite Hitch Lock and Anti-Rattle Device # THSTL2

expert reply by: Kyle S

0

Answer 1

The Thule anti-sway angled extensions #852-3108-001 can be removed from the Hold Fast cradle the reverse way they are installed. I have attached a photo from the Vertex instructions showing how they are installed. The angled extension will rotate so…

view full answer...

Answer 2

I spoke with my contact at Thule and she informed me that you could use the Replacement T3 Cradle #853-5829 as replacement cradles on your Thule 996 Expressway bike rack. For a strap you would want a Replacement Rubber Strap #753-3535.

view full answer...

Answer 3

Since the Thule T3 cradle assembly has been discontinued, your only option is to replace the cradle as well. For your Thule Expressway 996, is the Replacement Rubber Strap for Thule T2 Bike Carrier Cradles #753-3535, with its corresponding cradle…

view full answer...

Answer 4

There are currently several different Thule Hitching Post 4-Bike Racks (980, 944, 945, 984, 985, 934, 934 XT, 935, 935XT, Etc.) so it would be a bit difficult to confirm the correct replacement parts without the exact model. If you don't know…

view full answer...

Answer 5

Installation of the T3 cradle replacement strap is pretty straight forward. You will need to remove the end cap from the end of the bike support arm, a Phillips screw typically holds the cap in place. Next use a small amount of soap and water to help…

view full answer...

Answer 6

Hey Joseph, for your Thule Vertex 9029XT the correct replacement end cap is the part #TH8523293001 and then for the frame cradle you would want the part #852-3005-002. Do you need any other parts?

view full answer...

Answer 7

The correct replacement cradle and straps for your Thule Vertex 4 Bike 9029 is the Replacement Hold Fast Cradle for Thule Vertex Bike Racks - Qty 1 #852-3005-002 and the Replacement Straps for Cradles on Thule Bike Racks - Qty 4 #TH534.

view full answer...

Answer 8

You would need to remove that rivet, which is what you have shown in your photo. To remove it, find a drill bit small enough to insert through the center hole. Then use the next size up. you should only need to drill in less than a quarter of an inch…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Replacement Hitch Lock For Thule Expressway 996XT Bike Rack

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching