Fantastic Vent 3300 Compatibility With 3350 Model

Question

Question:

I only need to replace the bottom part of the fan and leave in tacked the motor fan and housing, Are all the holes, Screws, and connections to the existing model plug and play?

asked by: Willie D

0

Expert Reply:

Yes, your current 3300 series is compatible with the Fan-Tastic Vent Roof Vent, # FV803350. It is plug and play for the lower portion same with any other fan model beginning with 33 for model number.

expert reply by: Michael R

0

Answer 1

Hey Garth, yes the Dometic FanTastic Roof Vent Assembly Upgrade Kit #FV807357 will work on your older Dometic fan. The frame design hasn't changed since then so it will bolt right up.

view full answer...

Answer 2

Hey Kevin! They do make an angled 50 amp cord. The SmartPlug Angled RV Power Cord - 50 Amp - 30' #SM54SB is what you're looking for.

view full answer...

Answer 3

Hey Frank, unfortunately the Dometic FanTastic Roof Vent Assembly Upgrade Kit #FV807357 is not going to work with your Fan-Tastic Fan 1450 because the lift arm is different. Your only option then is to replace the entire assembly with a brand new one…

view full answer...

Answer 4

The only difference I'm seeing between the Fan-Tastic Vent Roof Vent Assembly Upgrade Kit #FV807357 and Kit #FV807359 is that the 57 has small cutouts at the corners while the 59 has squared corners. Aside from that these are both labeled to work…

view full answer...

Answer 5

The Fan-Tastic Vent Roof Vent w/ 12V Fan and Remote part #FV807350 is a complete assembly that will completely replace an existing vent. The Fan-Tastic Vent Roof Vent Assembly Upgrade Kit part #FV807357 is designed as an add on to existing vents. The…

view full answer...

Answer 6

Richard, with your FanTastic 5250 vent being obsolete your only option is to upgrade it with the Kit #FV807357 you found. You may also need a new inner garnish which you can determine by following the instructions on the bottom of page 4 which I have…

view full answer...

Answer 7

The MaxxFan Deluxe Roof Vent w/ 12V Fan #MA00-07500K referenced in your question fits a 14 inch x 14 inch RV roof opening, but the mounting flange itself measures 16-1/2 inches x 16-1/2 inches. This will refer to the footprint of the unit from inside…

view full answer...

Answer 8

For a 2022 Ram 1500 we carry a few Bedslide options but they all have a 4-1/2" height so depending on the fridge/cooler you plan on hauling around you may run into some clearance issues with your RetraxPro tonneau cover. The Bedslide options we…

view full answer...

Answer 9

I did some checking and for the MaxxAir the correct replacement circuit board is the #MA39FR.

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Fantastic Vent 3300 Compatibility With 3350 Model

Continue Researching