How to Determine Fit of Dexter E-Z Flex Suspension Kit K71-656-00 For Triple Axle Trailer

Question

Question:

will this fit my 2006 weekend warior le 35? 35 foot triple axle?

asked by: Jeff B

0

Expert Reply:

I can tell you how to determine the fit of the Dexter E-Z Flex Suspension Kit - Double-Eye Springs - Triple Axle - 6,000 lbs # K71-656-00, but it isn't a fit for any specific trailer, and we don't have any way of knowing for certainty if it will fit your 2006 Weekend Warrior.

It's pretty easy to find out though; first, you just need to know the capacity of your axles, which should be up to 6,000 lbs (per axle), and the other thing you need to do is measure the space between your axles. For a triple axle trailer, measure from the center of your middle axle to the center of the axles on either side; if that spacing measures 33 inches you can use the Dexter E-Z Flex Suspension Kit - Double-Eye Springs - Triple Axle - 6,000 lbs # K71-656-00.

expert reply by: Kyle S

0

Answer 1

The correct set of replacement brake assemblies for your AxleTek 12 inch assemblies is the kit part #AKEBRK-7-SA that you referenced. This kit is a pair of left and right assemblies that are an exact match to what you have that are also self…

view full answer...

Answer 2

Hey Trailer Dude, if you check out the attached review video on this page down below you can see at the 3:20 mark our installer Jeff measures the equalizers that come with the part #K71-656-00 so you can see the exact dimensions. One of them is 5-3/4…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 5

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 6

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 7

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 8

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 9

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 10

The Dexter Nev-R-Adjust electric trailer brakes can be manually adjusted. There are a couple teeth of the adjustment wheel that are exposed just under the lever that you referenced. I have attached a photo showing the teeth. You will likely need a…

view full answer...

How to Determine Fit of Dexter E-Z Flex Suspension Kit K71-656-00 For Triple Axle Trailer

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching