Axletek-12-GG Replacement Brake Assembly and Hub Recommendation

Question

Question:

Needing to replace my brakes for my RV. Can you point me to the correct brakes and drums? Thanks!

asked by: Michael W

0

Expert Reply:

The correct set of replacement brake assemblies for your AxleTek 12 inch assemblies is the kit part # AKEBRK-7-SA that you referenced. This kit is a pair of left and right assemblies that are an exact match to what you have that are also self adjusting as well.

Then if you have a 6 lug hub/drum currently the correct replacement would be the part # AKHD-655-6-EZ-K or if you have an 8 lug hub you'd need # AKHD-865-7-G-EZ-K.

expert reply by: Jameson C

0

Answer 1

We carry both the Left #AKEBRK-7L-SA and Right #AKEBRK-7R-SA Electric Trailer Brake Assemblies to replace your AXLETEK-12-GG,

view full answer...

Answer 2

Trailer brake assembly #AKEBRK-7L-SA is a 12 x 2 inch assembly with a 5-bolt mounting pattern for 5.2K to 7K axles so it will fit in place of your existing 12 inch brakes! This is the left hand assembly. The matching right hand assembly is…

view full answer...

Answer 3

Dexter brake assemblies like the part #23-458-459 are essentially the best ones on the market. They use the best materials and and incredibly reliable and well-made. That being said the etrailer.com brand assemblies part #AKEBRK-7-SA are also very…

view full answer...

Answer 4

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 5

Hey Joe, For both you'll need the left hand assembly #DX79CR along with the right hand assembly #DX69CR. These have built-in manual parking brakes that you can attach a cable actuated lever #T2385200 to for an easier way to engage the parking…

view full answer...

Answer 6

We do carry the exact brakes that you need for your B12E-02 AxleTek 12-GG Axle. For the Left Assembly you will want part #AKEBRK-7L-SA and for the Right Hand assembly you will want part #AKEBRK-7R-SA. These brake assemblies are made by AxleTek and…

view full answer...

Answer 7

Hey Carson, from the part number you mentioned that would indicate you have a 7k axle so for a bearing kit that includes correct seal you would want the part #BK3-210.

view full answer...

Answer 8

The exact replacement hub assemblies you need for your BD2-545-17 are the etrailer Trailer Hub and Drum Assembly - 3,500-lb Axles - 10" Diameter - 5 on 4-1/2 #AKHD-545-35-K that you referenced.

view full answer...

Answer 9

Thanks for the picture! I checked with Progressive Dynamics the replacement power converter you need for your Parallax Series 7300 Model 7345 is the Replacement Converter for Parallax/Magnetek or WFCO RV Power Centers - 45 Amp item #PD4645V.

view full answer...

Answer 10

The "AXLETEK-12-GG" would cross-reference to our Electric Trailer Brake Kit part #AKEBRK-7-SA but these use a five bolt mounting flange. The four bolt mounting flange is used on smaller, 10" x 2-1/4" brakes, not 12" x 2"…

view full answer...

Answer 11

For the Titan model 60 drum brake surge coupler the replacement master cylinder kit is part #T4395100. This includes the master cylinder, gasket, orifice connector, hardware and cover. I linked both review and installation videos to help you.

view full answer...

Answer 12

To use the Westlake 215/75R17.5 radial tire and wheel, #LHAS701 is an 8 on 6-1/2 it may be possible to change your studs from 1/2" to 9/16" so long as the studs are drive-in (as opposed to threaded); also, the length and knurl diameter…

view full answer...

Axletek-12-GG Replacement Brake Assembly and Hub Recommendation

Product Page this Question was Asked From

Continue Researching