Brake Line Kits that Can Be Used with Dexter Disc Brake Assemblies

Question

Question:

Is there a brake line installation kit for this kit Dexter Disc Brake Kit - 10inch Hub/Rotor - 5 on 4-1/2 - E-Coat - 3,500 lbs

asked by: Robert H

0

Expert Reply:

Yes we do have Dexter brake lines that can be used with brake assemblies like the # K71-633-2 like with the part # HS496-252 for a tandem axle trailer or # 18SI-BLKIT which is for a single axle trailer.

expert reply by: Jameson C

0

Answer 1

I believe you are asking if the hubs/bearings that come with Dexter Disc Brake Kit part #K71-633-2 will work on a Shorelandr or Lund trailer. Since I do not have the ability to cross list bearings by manufacturer. The best way to determine which…

view full answer...

Answer 2

Hey Nicholas, thanks for reaching out! The rotors in the E-Coat Dexter Disc Brake Kit #K71-633-2 are being discontinued so even if we had everything else available separately in a different kit I'd recommend going with a different disc brake kit…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Brake Line Kits that Can Be Used with Dexter Disc Brake Assemblies

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching