Replacement Remote for Air Lift 16092 Compressor

Question

Question:

I have a 2012 Chevy Silverado 2500HD with a 16092 airlift compressor and 5813 air springs. The remote controller has gone AWOL and I need to get another one and directions on how to pair it to the unit that is in the truck. Help please

asked by: Tim

0

Expert Reply:

Since your Air Lift compressor is part 16092 the correct replacement remote is the part # AL73002. I attached a picture that covers the pairing process as well.

expert reply by: Jameson C

0

Pairing Instructions
(click to enlarge)

Answer 1

I spoke to Air Lift to confirm and the Replacement Wireless Remote AL73002 will work as a replacement for your 73001 remote. You will need 3-AAA Batteries #287-11407 that are not included to power on the new remote. Once you place the batteries into…

view full answer...

Answer 2

The air compressor part number 16092 tells me you have the Air Lift WirelessAIR Compressor System for Air Helper Springs part AL72000 and the correct replacement remote for this is the Replacement Wireless Remote for Air Lift WirelessAIR Compressor…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Replacement Remote for Air Lift 16092 Compressor

Continue Researching