Opening Handle On Yakima SkyBox 16 With The Key Cylinder Removed and The Handle Wont Open

Question

Question:

I tried the WD40 on the locks, removed the locks, and nothing. I need your help, how do I move the handle? It won’t budge, nor will the lock turn. Is there a way to drill it out to spin the handle, any recommendations?

asked by: Johnnie J

0

Expert Reply:

With the lock cylinder removed you will be able to see the hole that the lock protrudes into. This piece should move inside the handle to allow that locking mechanism to either lock the handle or release the handle.

If it will not move you may try some WD40 on the mechanism to see if it will break free and allow you to open the handle.

If the mechanism spins freely with no resistance it is likely that it is damaged and not engaging the lock properly. If this is the case you will have to have the Handle # Y8880348 replaced. To remove the handle you need to drill out the locking mechanism to get it free from the handle to be able to open your Yakima SkyBox 16 Roof Cargo Box.

expert reply by: Bud M

0

Answer 1

According to Yakima, the serial number is stamped into the plastic on the underside of the box next to one of the crossbar clamps.

view full answer...

Answer 2

Because all Yakima products use lock cores for the Same Key System, any Yakima lock core will work. In order to replace the lock cores you will need to get the broken keys out of the locks. Once you've gotten the broken keys out, then use the…

view full answer...

Answer 3

Hello John, thanks for reaching out. We do have the replacement lift hinges for the Yakima SkyBox 16. For that you can use the Replacement Lid Support for Yakima Cargo Boxes #8880684. That said, the pieces riveted to the top lid are not replaceable,…

view full answer...

Answer 4

I gave Yakima a call, and was told that if the key is turned midway between the lock and unlock position, it can then be removed. At that point, you would then insert the control key and remove and replace the lock core as desired. Check out the…

view full answer...

Answer 5

The Yakima Skybox 21 part #Y07337 made from 2014 to present has a much more aerodynamic shaped lid than the Yakima Skybox 21 part Y07184 made from 2009 to 2014 had. I have attached a photo of each so you can see the difference. If you have the 09-14…

view full answer...

Answer 6

If you have a newer Yakima SkyBox NX 16 like part #Y95AV then you should be able to just open the box from the other side. That said, there really isn't a good way to go about opening this without the latch installed. If you like you can try to…

view full answer...

Answer 7

Yes, the same instructions for removing the Replacement SuperLatch Handles for Yakima SkyBox Cargo Boxes Item #Y8880348 will work. If you can already remove the lock I recommend doing that if not you will just need to get the broken key out to remove…

view full answer...

Answer 8

The correct replacement handles for a Yakima SkyBox made from 2009 on is the Replacement SuperLatch Handle Assemblies for Yakima SkyBox Rooftop Cargo Boxes #Y8880348. These come in a quantity of two with lock cores and keys, so you have the right…

view full answer...

Answer 9

It sounds like your Skybox has already been tampered with as this is not normal at all. I recommend you replace the entire assembly using the Replacement SuperLatch Handle Assemblies for Yakima SkyBox Rooftop Cargo Boxes - Qty 2 #Y8880348. These…

view full answer...

Answer 10

I attached a picture that shows instructions for replacing the handle of your Skybox 16 part #Y07336 with the part #Y8880348 that you referenced. This handle hasn't changed since 2014. Depending on which Skybox you have and what year it was…

view full answer...

Answer 11

It is very difficult to diagnose what the issue may be without knowing a model number and seeing photos but it sounds like the latch on the locking mechanism on your RocketBox may have somehow been damaged. I would need to know the model number in…

view full answer...

Answer 12

Hello John. We do offer a replacement locking handle for the Yakima Skybox 12 #Y07334. For new handles I recommend using the Replacement SuperLatch Handles for Yakima SkyBox Cargo Boxes #Y8880348. This comes with a set of 2 handles and 2 keys. I know…

view full answer...

Opening Handle On Yakima SkyBox 16 With The Key Cylinder Removed and The Handle Wont Open

Product Page this Question was Asked From

Continue Researching