Dimensions of Crank Handle Included with ARK AR94FR Trailer Stabilizing Jack

Question

Question:

Can I get the dimensions of the winding handle/crank of the AR94FR Ark Drop Down Corner RV Stabilizer Jacks

asked by: ATTAR

0

Expert Reply:

You sure can!

The handle is 22-1/8 inches long overall, the remaining dimensions can be seen the provided photo.

expert reply by: Mike L

0

Dimensions of Crank Handle for ARK AR94FR Trailer Stabilizing Jack
(click to enlarge)

Answer 1

Hey John, while we have something that'll work for you, we don't have Strong Arm stabilizer kits for just the 2 rear jacks; only 4 jacks. You could opt to replace the scissor jacks with Ark Drop Down Corner RV Stabilizer Jacks - 30" Long…

view full answer...

Answer 2

You can install the Erickson Horizontal E-Track #E19148 in any manner you like, so for a car hauler that has cars of different widths you can place E-track side-by-side, as you can see one of our customers did in the accompanying photo. This E-track…

view full answer...

Answer 3

Hi Mike; the Ark Drop Down Corner RV Stabilizer Jacks #ARK77FR can be used in three different positions. At 30° and 60° they act as non-rated stabilizers. At 90° they have the 1,929 lb rating.

view full answer...

Answer 4

I've attached a dimensional drawing for the Ark XO Drop Down Corner RV Stabilizer Jacks #ARK87FR, which displays the measurements in mm and inches. If you need anything else please let me know and I'd be happy to help.

view full answer...

Answer 5

Hey Brent! I would mount the Ark Drop Down Corner RV Stabilizer Jacks #ARK94FR on the outside as close to the corners as possible. If you mount them in the center of the trailer they won't add nearly as much stability. If you're worried about…

view full answer...

Answer 6

Good question, and we have asked the manufacturer, Ark, this very same question, and they have said there is not any weight rating for the Ark Drop Down Corner RV Stabilizer Jacks - 33" Long Corner Steadies #ARK77FR. They say the reason they…

view full answer...

Answer 7

We do carry the 33" Ark Stabilizer Jack that you are looking for with part #ARK77FR. I was able to track down a few drawings that you should find helpful. These are for the 30" #ARK94FR and the 24" #ARK34FR Stabilizer jacks. I'm…

view full answer...

Answer 8

My contact at Ark said the mounting plate for the Ark XO Drop Down Corner RV Stabilizer Jacks #ARK87FR can be installed by modifying it and using countersunk bolts. Attached is a photo of the dimensions for you to reference (117mm long x 72.50mm wide…

view full answer...

Answer 9

The Ark Drop Down Corner RV Stabilizer Jacks - 2-1/2' Long Corner Steadies - Qty 2 #AR94FR are 19" long at their shortest and extend 11" to give you up to 30" to keep your camper stable. If you were referring to the brackets and…

view full answer...

Answer 10

The Ark Drop Down Corner RV Stabilizer Jacks - 33" #ARK77FR is the same as their part number: XODDS850BUS.

view full answer...

Answer 11

Hello Daniel, thanks for reaching out. The Ark Drop Down Corner RV Stabilizer Jacks #AR94FR are 19" long when fully retracted. They have 11" of travel so they go out to 30" long overall when fully extended. I edited a picture for you…

view full answer...

Answer 12

The weld-on mounting bracket for the ARK #AR94FR Drop Down Corner RV Stabilizer Jacks measures 4-5/8 x 2-7/8 inches. The bracket has holes for the hardware that attaches the jack to the brackets. The holes are 2-7/8 inches apart on center. I've…

view full answer...

Dimensions of Crank Handle Included with ARK AR94FR Trailer Stabilizing Jack

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching