Will Mad-Ramps Pivoting Ramp System For ATV/UTV Work On 2019 Honda Ridgeline?

Question

Question:

Will Mad-Ramps work with stock 2019 Honda Ridgeline?

asked by: Gregg

0

Expert Reply:

Yes, Mad-Ramps Pivoting Ramp System for ATV/UTV Ramps - 1,400-lbs # MR54FR will fit your 2019 Honda Ridgeline. It simply attaches to your 2" trailer hitch receiver and allows for safe loading of an ATV, UTV/side by side, or golf cart. The max wheel base is 88", the max width is 60", and the weight capacity is 1,400lbs. I attached a demonstration video for you to check out.

expert reply by: Andrew N

0

Answer 1

What you could do is install the Curt ATV hitch part #C45006 on your ATV and then use a ball mount with a 4 inch rise like the part #C45070 and then for a 2 inch ball part #63845. Finally for a hitch pin part #C21500.

view full answer...

Answer 2

There's actually a much simpler solution for wiring your 2023 Ford Bronco with LED taillights to be flat towed with the Roadmaster smart diode kit part #RM38FR.This will wire your separate taillight circuits to function like a combined setup when…

view full answer...

Answer 3

According to Dexter your axle uses a 10-19 grease seal which would be the #58846. If you need a pair you can use part #RG06-050.

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The trailer brakes work on a separate circuit than the lights. You have a couple of options to control the electric brakes on the trailer. One option is to use an air over electric brake control, #HA100400C. This unit connects to the air brakes on…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Actually, the P3 now has the upgraded axis accelerometer like the P2. The Tekonsha P3 Trailer Brake Controller #90195, will work with both electric over hydraulic brakes on the trailer as well as electric brakes. It has a menu option on the display…

view full answer...

Answer 11

Hey James, you can go with a 4k axle leaf spring like the part #e22YR in place of what you have now while it has a slightly higher weight capacity it's not enough that it would create a harsh ride quality. This is a 26 inch long spring though so…

view full answer...

Answer 12

Hey Arny, yes the 2020 GMC Sierra 1500 AT4 does require the spacer part #F2366 with the Firestone kit part #F2609 since it has a factory 2 inch lift kit.

view full answer...

Will Mad-Ramps Pivoting Ramp System For ATV/UTV Work On 2019 Honda Ridgeline?

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching