Looking for Replacement Breakaway Switch for Brake Buddy Classic

Question

Question:

Is this switch normal closed i need it for my brake buddy classic will this work or witch one do you have that will thanks

asked by: Monty

0

Expert Reply:

Hey Monty, I did some checking and the breakaway switch part # RVI97FR that you referenced is the correct breakaway replacement for your Brake Buddy Classic. What are you flat towing?

expert reply by: Jameson C

0

Monty

5/11/2026

2024 Ford Bronco Heritage limited 2 door

Jameson C.

5/12/2026

@Monty nice! Do you have the rest of your flat towing setup picked out?

Monty

5/12/2026

No I need base plate kit I have the Curt Rambler tow bar and 7 to 6 light wiring kit for my Bronco also want a trailer wiring kit for the Bronco also and battery trickle charger kit from RV To Bronco what products do you recommend

Jameson C.

5/12/2026

@Monty You would need the Curt base plate kit part # C83ZV, for lighting do you have more than just the 6 to 7 adapter or do you need like a diode kit? And then for a charge line kit part # RM-156-25.

See All (5) Replies to Monty ∨

Answer 1

The Second Vehicle Breakaway Kit for Blue Ox Patriot Supplemental Braking Systems #BRK2505 is designed to work with the Blue Ox Patriot BRK2012 (NLA), Patriot II BRK2010 (NLA), BRK2016 (NLA), or the Patriot 3 BRK2019 (NLA). Unfortunately, this will…

view full answer...

Answer 2

The complete replacement breakaway kit for a Hopkins Brake Buddy II is the part #HM39340 but since you only want the switch Fred and it's a universal switch that is used you could use the part #C52010 and be fine.

view full answer...

Answer 3

The Replacement Breakaway System for Brake Buddy Classic and Select Supplemental Braking Systems part #HM39340 replaces the brake away switch for the brake buddy Classic II, Select II, Classic 3 (#HM39494), and Select 3 (#HM39524). We have not yet…

view full answer...

Answer 4

Hey Mark, For a Brake Buddy Vantage supplemental braking system you would need the Replacement Breakaway Kit for Brake Buddy Vantage Select Flat Tow Brake System #HM39327.

view full answer...

Answer 5

I went out to the warehouse and pulled Pollak 6-pole vehicle side connector #PK11608 to measure the mounting hole spacing for you. The holes are 2-3/4 inches apart on center. The vehicle and trailer side connectors are different. The trailer side…

view full answer...

Answer 6

On a 6-Pole, Round Pin, Plastic Trailer Wiring Socket #PK12720 there is typically only enough room for one wire for each terminal to mount inside the stud. You can still splice both the ground wires together and run a single wire into the terminal on…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...

Looking for Replacement Breakaway Switch for Brake Buddy Classic

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching