Availability Of Replacement Mounting Hardware For Curt Front Mount Trailer Hitch C31063

Question

Question:

I am putting this front mount hitch on a second Ranger and need a new set of bolts, washers and spring Chace wire. Is there a kit for these?

asked by: Richard P

0

Expert Reply:

There sure is!

To order the replacement mounting hardware for the Curt Front Mount Trailer Hitch Receiver # C31063 you have you will need the Replacement Hardware Kit # RHK.

You will need to select Curt from the drop down menu, and then enter 31063 as the hitch item number. This will include all of the components needed including the fish wire.

I included a video of the # RHK for you to take a look at.

expert reply by: Samuel C

0

Answer 1

While we don't have just the CM-SP12 spacers for the Curt Trailer Hitch Receiver #C13362, you can either get a complete replacement hardware kit with part #RHK or you can just get 2 of the Trailer Hitch Spacer Block - 3" Long x 1" Wide…

view full answer...

Answer 2

We do not offer the Cm-S19 spacer as a separate item. It is available as part of the replacement hardware kit for installation of your Curt Trailer Hitch, part #C13264. To order the replacement hardware kit you can type #RHK in the search box on our…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 5

I am going to need to know what size trailer tire you have as there are several different size tires which fit an 8" wheel. I do see the Loadstar K399 Bias Trailer Tire #AM1HP26 is our highest speed rated tire for an 8" x 7" Wheel…

view full answer...

Answer 6

The installation instructions for Curt front-mount hitch #C31063, which are linked for you, show that the two mounting flanges for this hitch each have two holes for hardware installation on the mating holes in the frame rails. You can compare the…

view full answer...

Answer 7

For your 1994 Ford Ranger I recommend the Detail K2 Avalanche Snowplow #K2AVAL8422 which fits in the Curt Front-Mounted Hitch #C31063 (please keep in mind this hitch will not fit Ranger's with a front cross-member or 2WD models built in Canada).…

view full answer...

Answer 8

Hi David; we don't have a way for you to mail it to us so you will have to identify the hub to find the right replacement. Identifying the hub is pretty easy and will save you money since you won't have to pay to ship a hub. Based on the bolt…

view full answer...

Answer 9

The thickness of the rotor on Kodiak 12-Inch Hub-and-Rotor Assembly #KHR12D is 0.930-inch (23.6mm). I confirmed this dimension with my technical contact at Kodiak. Naturally this starting thickness will gradually be reduced from use.

view full answer...

Answer 10

The Curt Front Mount Receiver, item #31352, has a 9,000 Lbs. Max. Line Pull, and lower fascia trimming may be required on some models. The part that may need to be trimmed is the plastic fascia that is attached to the bottom of the chrome bumper on…

view full answer...

Answer 11

Hi Dustin; as long as you measured pictures aren't necessary. However, I can tell you we don't have a hinge kit for a 2" x 4" trailer tongue. I also ran an internet search and could not find one for those dimensions. Unless you are…

view full answer...

Availability Of Replacement Mounting Hardware For Curt Front Mount Trailer Hitch C31063

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching