Solution for Hitch Install that Hits Exhaust and Makes Noise
Updated 08/09/2021 | Published 08/07/2021
Question:
After installing the Curt CU64FR on my 2015 Subaru Forester, the rubber exhaust hanger hits the hitch causing the tailpipe to not be centered in the opening for it. I am worried about the tailpipe burning the bumper it is so close. Also, I am worried that the hitch will eventually cut through the rubber hangar. Any ideas what to do?
asked by: Gary H
Expert Reply:
Exhaust rattle is fairly common problem with hitch installs that can easily be fixed. Since exhaust systems are designed for slight movements they don't always sit in the same spot on every vehicle, so when a hitch is designed for a vehicle the hitch might sit close and not rattle on one vehicle, but on another vehicle the clearances might be different and the exhaust might hit the hitch.
To see how to address the exhaust rattle you are experiencing check out the video I attached to this page. Basically you are going to need to bend your exhaust hangers or go with different length isolators.
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- For Towing
- Class III
- 525 lbs TW
- 3500 lbs GTW
- 2 Inch Hitch
- Concealed Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Trailer Hitch
- Shop: Trailer Wiring
- Video: FAQ Trailer Hitch Exhaust Rattle
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Video: Set up: Curt Trailer Hitch Receiver on a 2017 Subaru Forester
- Video: Installation Guide for the Curt Trailer Hitch Receiver on a 2016 Subaru Forester
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Video: Curt Custom Fit Vehicle Wiring - Trailer Hitch Wiring - C55312 Review
- Video: Oris Class III Detachable Receiver Trailer Hitch DIY Installation - 2025 BMW X5
- Shop: Vehicle Tow Bar Wiring
- Search Results: ball covers
- Search Results: soccer ball hitch covers
- Search Results: hitch ball covers
- Search Results: trailer hitch ball accessories and parts
- Q&A: Comparing the Curt Hitch CU64FR and Draw-Tite Hitch 76182 for a 2017 Subaru Forester
- Q&A: Differences Between Curt Class III Trailer Hitches for 2015 Subaru Forester
- Q&A: 2016 Subaru Forester XT Touring Exhaust Rattle After Hitch Install
- Q&A: Recommended Trailer Hitch and Towing Accessories for 2015 Subaru Forester
- Shop: Curt Class III Ball Mount with 2" Ball - 4" Drop - 2" Rise - 7,500 lbs
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Convert-A-Ball Interchangeable Hitch Ball - 2-5/16" Diameter - Nickel-Plated Steel
- Shop: Curt Towing Starter Kit for 2" Hitches - 2" Ball - 3/4" Rise, 2" Drop - 7.5K
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Search Results: trailer hitch
- Video: Curt T-Connector Vehicle Wiring Harness Review C56040
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Search Results: trailer wiring
- Video: The Low-Down on the Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
on Trailer Hitch
