Recommended PSI Rating For A 2020 Lance 1985 Travel Trailer

Question

Question:

I have a 2020 Lance model 1985 and wondering if I should use a 40-50 lb reducer or a 50-55 reducer. I bought both. Could the 50-55 lb damage my water lines, faucets, etc?

asked by: Jeff E

0

Expert Reply:

Most newer model RV's can handle up to 100PSI but it's recommended to stay under 60PSI. Most manufacturers recommend keeping the PSI in the 40-50 range with a regulator like the # 37262205 but the 50-55 range reducer you bought shouldn't hurt anything.

expert reply by: Kevin C

0

Answer 1

Hey Joseph. Since your 2022 Ram 2500 has the factory air suspension, I recommend adding the Timbren Rear Suspension Enhancement System item #TDR2500D. These progressive rate springs install where your bump stops are currently mounted. The more weight…

view full answer...

Answer 2

There are several ways that you can cut off the power to your trailer brakes. The easiest option would be to simply unplug your brake controller. If the brake controller is disconnected, the brakes will not receive power. If your brake controller was…

view full answer...

Answer 3

Hello Bill, that is an interesting question. If one of your brake assemblies is getting constant 12v power and locking up, then yes, cutting the wire would release the magnet and stop the brake from engaging. If something else is causing the brake to…

view full answer...

Answer 4

It's a safe bet that when your Fan-Tastic Vent #FV807350 starts having a mind of its own that a damaged circuit board is the culprit. The circuit board can be replaced but will require you to use the Fan-Tastic Vent 7350 Series Upgrade Kit…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 12

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Recommended PSI Rating For A 2020 Lance 1985 Travel Trailer

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching